- 您现在的位置：买卖IC网 > PDF目录378586 > DS12CR885 (Maxim Integrated Products, Inc.) RTC with Constant-Voltage Trickle Charger PDF资料下载
参数资料
| 型号： | DS12CR885 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | RTC with Constant-Voltage Trickle Charger |
| 中文描述： | 时钟与恒压涓流充电器 |
| 文件页数： | 19/22页 |
| 文件大小： | 1093K |
| 代理商： | DS12CR885 |
D
RTC with Constant-Voltage Trickle Charger
____________________________________________________________________
19
Nonvolatile RAM (NV RAM)
The 114 general-purpose NV RAM bytes are not dedi-
cated to any special function within the DS12R885.
They can be used by the processor program as
battery-backed memory and are fully available during
the update cycle.
Interrupts
The DS12R885 includes three separate, fully automatic
sources of interrupt for a processor. The alarm interrupt
can be programmed to occur at rates from once per
second to once per day. The periodic interrupt can be
selected for rates from 500ms to 122μs. The update-
ended interrupt can be used to indicate to the program
that an update cycle is complete. Each of these inde-
pendent interrupt conditions is described in greater
detail in other sections of this text.
The processor program can select which interrupts, if
any, are to be used. Three bits in Register B enable the
interrupts. Writing a logic 1 to an interrupt-enable bit
permits that interrupt to be initiated when the event
occurs. A 0 in an interrupt-enable bit prohibits the
IRQ
pin from being asserted from that interrupt condition. If
an interrupt flag is already set when an interrupt is
enabled,
IRQ
is immediately set at an active level,
although the interrupt initiating the event may have
occurred earlier. As a result, there are cases where the
program should clear such earlier initiated interrupts
before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is
set to logic 1 in Register C. These flag bits are set inde-
pendent of the state of the corresponding enable bit in
Register B. The flag bit can be used in a polling mode
without enabling the corresponding enable bits. The
interrupt flag bit is a status bit that software can interro-
gate as necessary. When a flag is set, an indication is
given to software that an interrupt event has occurred
since the flag bit was last read; however, care should
be taken when using the flag bits as they are cleared
each time Register C is read. Double latching is includ-
ed with Register C so that bits that are set remain sta-
ble throughout the read cycle. All bits that are set (high)
are cleared when read, and new interrupts that are
pending during the read cycle are held until after the
cycle is completed. One, two, or three bits can be set
when reading Register C. Each used flag bit should be
examined when Register C is read to ensure that no
interrupts are lost.
The second flag bit method is used with fully enabled
interrupts. When an interrupt flag bit is set and the cor-
responding interrupt-enable bit is also set, the
IRQ
pin
is asserted low.
IRQ
is asserted as long as at least one
of the three interrupt sources has its flag and enable
bits set. The IRQF bit in Register C is a 1 whenever the
IRQ
pin is driven low. Determination that the RTC initiat-
ed an interrupt is accomplished by reading Register C.
A logic 1 in bit 7 (IRQF bit) indicates that one or more
interrupts have been initiated by the DS12R885. The
act of reading Register C clears all active flag bits and
the IRQF bit.
Oscillator Control Bits
When the DS12R887 and DS12CR887 are shipped
from the factory, the internal oscillator is turned off. This
feature prevents the lithium energy cell from being
used until it is installed in a system.
A pattern of 010 in bits 4 to 6 of Register A turns the
oscillator on and enables the countdown chain. A pat-
tern of 11x (DV2 = 1, DV1 = 1, DV0 = X) turns the oscil-
lator on, but holds the countdown chain of the oscillator
in reset. All other combinations of bits 4 to 6 keep the
oscillator off.
Square-Wave Output Selection
Thirteen of the 15 divider taps are made available to a 1-
of-16 multiplexer, as shown in the functional diagram.
The square-wave and periodic-interrupt generators
share the output of the multiplexer. The RS0–RS3 bits in
Register A establish the output frequency of the multi-
plexer (see
Table
1). Once the frequency is selected, the
output of the SQW pin can be turned on and off under
program control with the square-wave enable bit, SQWE.
Periodic Interrupt Selection
The periodic interrupt causes the
IRQ
pin to go to an
active state from once every 500ms to once every
122μs. This function is separate from the alarm inter-
rupt, which can be output from once per second to
once per day. The periodic interrupt rate is selected
using the same Register A bits that select the square-
wave frequency (
Table
1). Changing the Register A bits
affects the square-wave frequency and the periodic-
interrupt output. However, each function has a separate
enable bit in Register B. The SQWE bit controls the
square-wave output. Similarly, the PIE bit in Register B
enables the periodic interrupt. The periodic interrupt
can be used with software counters to measure inputs,
create output intervals, or await the next needed soft-
ware function.
相关PDF资料 |
PDF描述 |
|---|---|
| DS12CR887 | RTC with Constant-Voltage Trickle Charger |
| DS12CR887-33 | RTC with Constant-Voltage Trickle Charger |
| DS12CR887-5 | RTC with Constant-Voltage Trickle Charger |
| DS12R885 | RTC with Constant-Voltage Trickle Charger |
| DS12R885-33 | RTC with Constant-Voltage Trickle Charger |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS12CR887-33 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12CR887-33+ | 功能描述:实时时钟 RTC w/Constant V Trickle Charger RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12CR887-5 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12CR887-5+ | 功能描述:实时时钟 RTC w/Constant V Trickle Charger RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS12R885-33 | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK MULTIPLEXED 114BYTE - Bulk |
发布紧急采购，3分钟左右您将得到回复。