参数资料
| 型号： | DS1305E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 22/22页 |
| 文件大小： | 0K |
| 描述： | IC RTC SERIAL ALARM 20-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 74 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，NVSRAM，涓流充电器 |
| 存储容量： | 96B |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | SPI |
| 电源电压： | 2 V ~ 5.5 V |
| 电压 - 电源，电池： | 2 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1433 (CN2011-ZH PDF) |
DS1305
9 of 22
Table 3. TRICKLE CHARGER RESISTOR AND DIODE SELECT
TCS
Bit 7
TCS
Bit 6
TCS
Bit 5
TCS
Bit 4
DS
Bit 3
DS
Bit 2
RS
Bit 1
RS
Bit 0
FUNCTION
X
0
Disabled
X
0
X
Disabled
X
1
X
Disabled
1
0
1
0
1
0
1
1 Diode, 2k
1
0
1
0
1
0
1 Diode, 4k
1
0
1
0
1
1 Diode, 8k
1
0
1
0
1
0
1
2 Diodes, 2k
1
0
1
0
1
0
1
0
2 Diodes, 4k
1
0
1
0
1
0
1
2 Diodes, 8k
0
1
0
1
0
Initial power-on state
The user determines diode and resistor selection according to the maximum current desired for battery or
super cap charging. The maximum charging current can be calculated as illustrated in the following
example. Assume that a system power supply of 5V is applied to VCC1 and a super cap is connected to
VCC2. Also assume that the trickle charger has been enabled with 1 diode and resister R1 between VCC1
and VCC2. The maximum current IMAX would, therefore, be calculated as follows:
IMAX = (5.0V - diode drop) / R1 (5.0V - 0.7V) / 2k 2.2mA
As the super cap charges, the voltage drop between VCC1 and VCC2 decreases and, therefore, the charge
current decreases.
POWER CONTROL
Power is provided through the VCC1, VCC2, and VBAT pins. Three different power-supply configurations
are illustrated in Figure 4. Configuration 1 shows the DS1305 being backed up by a nonrechargeable
energy source such as a lithium battery. In this configuration, the system power supply is connected to
VCC1 and VCC2 is grounded. The DS1305 is write-protected if VCC1 is less than VBAT. The DS1305 is fully
accessible when VCC1 is greater than VBAT + 0.2V.
Configuration 2 illustrates the DS1305 being backed up by a rechargeable energy source. In this case, the
VBAT pin is grounded, VCC1 is connected to the primary power supply, and VCC2 is connected to the
secondary supply (the rechargeable energy source). The DS1305 operates from the larger of VCC1 or
VCC2. When VCC1 is greater than VCC2 + 0.2V (typical), VCC1 powers the DS1305. When VCC1 is less than
VCC2, VCC2 powers the DS1305. The DS1305 does not write-protect itself in this configuration.
Configuration 3 shows the DS1305 in battery operate mode where the device is powered only by a single
battery. In this case, the VCC1 and VBAT pins are grounded and the battery is connected to the VCC2 pin.
Only these three configurations are allowed. Unused supply pins must be grounded.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T21B35PC | CONN RCPT 79POS JAM NUT W/PINS |
| MS27468T21B35PB | CONN RCPT 79POS JAM NUT W/PINS |
| DS1340C-33# | IC RTC I2C W/CHARGER 16-SOIC |
| DS1306+ | IC RTC SERIAL ALARM 16-DIP |
| MS27468E21B35PB | CONN RCPT 79POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1305E/R | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
| DS1305E/T | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
| DS1305E/T&R | 制造商:Maxim Integrated Products 功能描述:IC RTC SERIAL ALARM 20-TSSOP |
| DS1305E/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1305E/TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Serial Alarm Real-Time Clock |
发布紧急采购，3分钟左右您将得到回复。