- 您现在的位置：买卖IC网 > PDF目录97859 > DS1306 (MAXIM INTEGRATED PRODUCTS INC) 0 TIMER(S), REAL TIME CLOCK, PDIP16 PDF资料下载
参数资料
| 型号： | DS1306 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Timer or RTC |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDIP16 |
| 封装： | 0.300 INCH, PLASTIC, DIP-16 |
| 文件页数： | 22/22页 |
| 文件大小： | 318K |
| 代理商： | DS1306 |
DS1306
9 of 22
Table 3. TRICKLE CHARGER RESISTOR AND DIODE SELECT
TCS
Bit 7
TCS
Bit 6
TCS
Bit 5
TCS
Bit 4
DS
Bit 3
DS
Bit 2
RS
Bit 1
RS
Bit 0
FUNCTION
X
0
Disabled
X
0
X
Disabled
X
1
X
Disabled
1
0
1
0
1
0
1
1 Diode, 2k
1
0
1
0
1
0
1 Diode, 4k
1
0
1
0
1
1 Diode, 8k
1
0
1
0
1
0
1
2 Diodes, 2k
1
0
1
0
1
0
1
0
2 Diodes, 4k
1
0
1
0
1
0
1
2 Diodes, 8k
0
1
0
1
0
Initial power-on state
If RS is 00, the trickle charger is disabled independently of TCS.
Diode and resistor selection is determined by the user according to the maximum current desired for
battery or super cap charging. The maximum charging current can be calculated as illustrated in the
following example. Assume that a system power supply of 5V is applied to VCC1 and a super cap is
connected to VCC2. Also assume that the trickle charger has been enabled with one diode and resister R1
between VCC1 and VCC2. The maximum current IMAX would, therefore, be calculated as follows:
IMAX = (5.0V - diode drop) / R1 (5.0V - 0.7V) / 2k 2.2mA
As the super cap charges, the voltage drop between VCC1 and VCC2 decreases and, therefore, the charge
current decreases.
POWER CONTROL
Power is provided through the VCC1, VCC2, and VBAT pins. Three different power supply configurations
are illustrated in Figure 4. Configuration 1 shows the DS1306 being backed up by a non-rechargeable
energy source such as a lithium battery. In this configuration, the system power supply is connected to
VCC1 and VCC2 is grounded. When VCC falls below VBAT the device switches into a low-current battery
backup mode. Upon power-up, the device switches from VBAT to VCC when VCC is greater than
VBAT + 0.2V. The device is write-protected whenever it is switched to VBAT.
Configuration 2 illustrates the DS1306 being backed up by a rechargeable energy source. In this case, the
VBAT pin is grounded, VCC1 is connected to the primary power supply, and VCC2 is connected to the
secondary supply (the rechargeable energy source). The DS1306 operates from the larger of VCC1 or
VCC2. When VCC1 is greater than VCC2 + 0.2V (typical), VCC1 powers the DS1306. When VCC1 is less than
VCC2, VCC2 powers the DS1306. The DS1306 does not write-protect itself in this configuration.
Configuration 3 shows the DS1306 in battery-operate mode, where the device is powered only by a single
battery. In this case, the VCC1 and VBAT pins are grounded and the battery is connected to the VCC2 pin.
Only these three configurations are allowed. Unused supply pins must be grounded.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1306E | 0 TIMER(S), REAL TIME CLOCK, PDSO20 |
| DS1306EN | 0 TIMER(S), REAL TIME CLOCK, PDSO20 |
| DS1307Z | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| DS1307N | 1 TIMER(S), REAL TIME CLOCK, PDIP8 |
| DS1307ZN | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1306_05 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Serial Alarm Real-Time Clock |
| DS1306+ | 功能描述:实时时钟 Serial Alarm RTC 3-Wire RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1306E | 功能描述:实时时钟 Serial Alarm RTC 3-Wire RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1306E/T&R | 制造商:Maxim Integrated Products 功能描述:IC RTC SERIAL ALARM 20-TSSOP |
| DS1306E/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。