- 您现在的位置：买卖IC网 > PDF目录9397 > DS1337U+ (Maxim Integrated Products)IC RTC SERIAL 2WIRE LP 8-USOP PDF资料下载
参数资料
| 型号： | DS1337U+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC RTC SERIAL 2WIRE LP 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，方波输出，涓流充电器 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.3 V ~ 1.8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
| 产品目录页面： | 1433 (CN2011-ZH PDF) |
DS1337 I
2C Serial Real-Time Clock
Figure 2. Data Transfer on I2C Serial Bus
Depending upon the state of the R/
W bit, two types of data transfer are possible:
1)
Data transfer from a master tr ansmitter to a slave receiver. The first byte transmitted by the master is the
slave address. Next follows a number of data bytes. The slave returns an acknowledge bit after each received
byte. Data is transferred with the most significant bit (MSB) first.
2)
Data transfer from a slave transmitter to a master receiver. The master transmits the first byte (the slave
address). The slave then returns an acknowledge bit, followed by the slave transmitting a number of data
bytes. The master returns an acknowledge bit after all received bytes other than the last byte. At the end of the
last received byte, a “not acknowledge” is returned. The master device generates all of the serial clock pulses
and the START and STOP conditions. A transfer is ended with a STOP condition or with a repeated START
condition. Since a repeated START condition is also the beginning of the next serial transfer, the bus is not
released. Data is transferred with the most significant bit (MSB) first.
The DS1337 can operate in the following two modes:
1)
Slave Receiver Mode (Write M ode): Serial data and clock are received through SDA and SCL. After each
byte is received an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception of the
slave address and direction bit (Figure 3). The slave address byte is the first byte received after the master
generates the START condition. The slave address byte contains the 7-bit DS1337 address, which is 1101000,
followed by the direction bit (R/
W), which, for a write, is 0. After receiving and decoding the slave address byte
the device outputs an acknowledge on the SDA line. After the DS1337 acknowledges the slave address +
write bit, the master transmits a register address to the DS1337. This sets the register pointer on the DS1337.
The master may then transmit zero or more bytes of data, with the DS1337 acknowledging each byte received.
The address pointer will increment after each data byte is transferred. The master generates a STOP condition
to terminate the data write.
2)
Slave Transmitter Mode (Read Mode): The first byte is received and handled as in the slave receiver mode.
However, in this mode, the direction bit indicates that the transfer direction is reversed. Serial data is
transmitted on SDA by the DS1337 while the serial clock is input on SCL. START and STOP conditions are
recognized as the beginning and end of a serial transfer (Figure 4 and Figure 5). The slave address byte is the
first byte received after the master generates a START condition. The slave address byte contains the 7-bit
DS1337 address, which is 1101000, followed by the direction bit (R/
W), which, for a read, is 1. After receiving
and decoding the slave address byte the device outputs an acknowledge on the SDA line. The DS1337 then
begins to transmit data starting with the register address pointed to by the register pointer. If the register
pointer is not written to before the initiation of a read mode the first address that is read is the last one stored in
the register pointer. The DS1337 must receive a “not acknowledge” to end a read.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1337+ | IC RTC SERIAL 2WIRE LP 8-DIP |
| MAX5481ETE+ | IC 10BIT NONVOL DGTL POT 16-TQFN |
| VE-J02-MZ | CONVERTER MOD DC/DC 15V 25W |
| MAX5484EUD+ | IC DGTL POT 10BIT NV 14-TSSOP |
| VE-J01-MZ | CONVERTER MOD DC/DC 12V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1337U/T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC SERIAL 2WIRE LP 8-USOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C Serial RTC |
| DS1337U/T&R | 功能描述:实时时钟 I2C Serial RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1337U+ | 功能描述:实时时钟 I2C Serial RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1337U+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
| DS1337U+T&R | 制造商:Maxim Integrated Products 功能描述:SERIAL RTC 8PIN USOP TRL LEADFREE 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC SERIAL 2WIRE LP 8-USOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C Serial RTC |
发布紧急采购，3分钟左右您将得到回复。