- 您现在的位置：买卖IC网 > PDF目录9369 > DS1339U-3+T&R (Maxim Integrated Products)IC RTC I2C W/ALARM 8-USOP PDF资料下载
参数资料
| 型号： | DS1339U-3+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC RTC I2C W/ALARM 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，方波输出，涓流充电器 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 3.3 V |
| 电压 - 电源，电池： | 1.3 V ~ 3.7 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS1339 I
2C Serial Real-Time Clock
12 of 20
TIME AND DATE OPERATION
The time and date information is obtained by reading the appropriate register bytes. Table 3 shows the RTC
registers. The time and date are set or initialized by writing the appropriate register bytes. The contents of the time
and date registers are in the BCD format. The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
hours register is defined as the 12- or 24-hour mode-select bit. When high, the 12-hour mode is selected. In the
12-hour mode, bit 5 is the
AM/PM bit with logic high being PM. In the 24-hour mode, bit 5 is the 20-hour bit (20 to
23 hours). All hours values, including the alarms, must be re-entered whenever the 12/
24-hour mode bit is
changed. The century bit (bit 7 of the month register) is toggled when the years register overflows from 99 to 00.
The day-of-week register increments at midnight. Values that correspond to the day of week are user-defined, but
must be sequential (i.e., if 1 equals Sunday, then 2 equals Monday and so on). Illogical time and date entries result
in undefined operation.
When reading or writing the time and date registers, secondary (user) buffers are used to prevent errors when the
internal registers update. When reading the time and date registers, the user buffers are synchronized to the
internal registers on any START or STOP, and when the address pointer rolls over to zero. The countdown chain
is reset whenever the seconds register is written. Write transfers occurs on the acknowledge pulse from the
device. To avoid rollover issues, once the countdown chain is reset, the remaining time and date registers must be
written within one second. If enabled, the 1Hz square-wave output transitions high 500ms after the seconds data
transfer, provided the oscillator is already running.
ALARMS
The DS1339 contains two time of day/date alarms. Alarm 1 can be set by writing to registers 07h to 0Ah. Alarm 2
can be set by writing to registers 0Bh to 0Dh. The alarms can be programmed (by the Alarm Enable and INTCN
bits of the Control Register) to activate the SQW/
INT output on an alarm match condition. Bit 7 of each of the time
of day/date alarm registers are mask bits (Table 4). When all the mask bits for each alarm are logic 0, an alarm
only occurs when the values in the timekeeping registers 00h to 06h match the values stored in the time of
day/date alarm registers. The alarms can also be programmed to repeat every second, minute, hour, day, or date.
Table 4 shows the possible settings. Configurations not listed in the table result in illogical operation.
The DY/
DT bits (bit 6 of the alarm day/date registers) control whether the alarm value stored in bits 0 to 5 of that
register reflects the day of the week or the date of the month. If DY/
DT is written to a logic 0, the alarm is the result
of a match with date of the month. If DY/
DT is written to a logic 1, the alarm is the result of a match with day of the
week.
The device checks for an alarm match once per second. When the RTC register values match alarm register
settings, the corresponding Alarm Flag ‘A1F’ or ‘A2F’ bit is set to logic 1. If the corresponding Alarm Interrupt
Enable ‘A1IE’ or ‘A2IE’ is also set to logic 1 and the INTCN bit is set to logic 1, the alarm condition activates the
SQW/
INT) signal. If the BBSQI bit is set to 1, the INT output activates while the part is being powered by V
BACKUP.
The alarm output remains active until the alarm flag is cleared by the user.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JN2-MZ | CONVERTER MOD DC/DC 15V 25W |
| VI-J5F-MZ | CONVERTER MOD DC/DC 72V 25W |
| VE-240-MX-B1 | CONVERTER MOD DC/DC 5V 75W |
| VE-BNZ-MY-F4 | CONVERTER MOD DC/DC 2V 20W |
| MS3450L22-2SZ | CONN RCPT 3POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1340 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with Trickle Charger |
| DS1340_06 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with Trickle Charger |
| DS1340_11 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with Trickle Charger |
| DS1340-3 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with Trickle Charger |
| DS1340C-18 | 功能描述:实时时钟 I2C RTC w/Trickle Charger RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。