参数资料
型号: DS1386-8-120
厂商: Maxim Integrated Products
文件页数: 21/21页
文件大小: 0K
描述: IC TIMEKEEPER RAM 64K 32-EDIP
标准包装: 11
类型: 时钟/日历
特点: 警报器,闰年,NVSRAM,方波输出,监视计时器
存储容量: 8KB
时间格式: HH:MM:SS:hh(12/24 小时)
数据格式: YY-MM-DD-dd
接口: 并联
电源电压: 4.5 V ~ 5.5 V
工作温度: 0°C ~ 70°C
安装类型: 通孔
封装/外壳: 32-DIP 模块(0.600",15.24mm)
供应商设备封装: 32-EDIP
包装: 管件
DS1386/1386P
9 of 21
COMMAND REGISTER
Address location 0Bh is the Command Register where mask bits, control bits and flag bits reside. The
operation of each bit is as follows:
Bit 7: TE (Transfer Enable). This bit when set to a logic 0 will disable the transfer of data between
internal and external clock registers. The contents in the external clock registers are now frozen and reads
or writes will not be affected with updates. This bit must be set to a logic 1 to allow updates.
Bit 6: IPSW (Interrupt Switch). When set to a logic 1,
INTA is the Time of Day Alarm and
INTB/(
INTB) is the Watchdog Alarm. When set to logic 0, this bit reverses the output pins. INTA is now
the watchdog alarm output and INTB/(
INTB) is the time of day alarm output.
Bit 5: IBH/LO (Interrupt B Sink or Source Current). When this bit is set to a logic 1 and VCC is
applied, INTB/(
INTB) will source current (see DC characteristics IOH). When this bit is set to a logic 0,
INTB will sink current (see DC characteristics IOL).
Bit 4: PU/LVL (Interrupt Pulse Mode or Level Mode). This bit determines whether both interrupts
will output a pulse or level signal. When set to a logic 0,
INTA and INTB/(INTB) will be in the level
mode. When this bit is set to a logic 1, the pulse mode is selected and
INTA will sink current for a
minimum of 3ms and then release. INTB/(
INTB) will either sink or source current, depending on the
condition of Bit 5, for a minimum of 3ms and then release. INTB will only source current when there is a
voltage present on VCC.
Bit 3: WAM (Watchdog Alarm Mask). When this bit is set to a logic 0, the watchdog interrupt output
will be activated. The activated state is determined by bits 1,4,5, and 6 of the Command Register. When
this bit is set to a logic 1, the watchdog interrupt output is deactivated.
Bit 2: TDM (Time-of-Day Alarm Mask). When this bit is set to a logic 0, the time of day alarm
interrupt output will be activated. The activated state is determined by bits 0,4,5, and 6 of the Command
Register. When this bit is set to a logic 1, the time of day alarm interrupt output is deactivated.
Bit 1: WAF (Watchdog Alarm Flag). This bit is set to a logic 1 when a watchdog alarm interrupt
occurs. This bit is read only. The bit is reset when any of the watchdog alarm registers are accessed.
When the interrupt is in the pulse mode (see bit 4 definition), this flag will be in the logic 1 state only
during the time the interrupt is active.
Bit 0: TDF (Time-of-Day Flag). This is a read-only bit. This bit is set to a logic 1 when a time of day
alarm has occurred. The time the alarm occurred can be determined by reading the time of day alarm
registers. This bit is reset to a logic 0 state when any of the time of day alarm registers are accessed.
When the interrupt is in the pulse mode (see bit 4 definition), this flag will be in the logic 1 state only
during the time the interrupt is active.
相关PDF资料
PDF描述
DS1556P-70 IC RTC RAM Y2K 5V 70NS 34-PCM
DS1315E-33 IC T-CHIP PHANTOM 3.3V 20-TSSOP
DS1315E-5 IC TIME CHIP PHANTOM 5V 20-TSSOP
DS1315N-33 IC T-CHIP PHANTOM 3.3V IND 16DIP
DS1556WP-120 IC RTC RAM Y2K 3.3V 120NS 34PCM
相关代理商/技术参数
参数描述
DS1386-8-120+ 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
DS1386-8-150 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS1386-8K 制造商:Maxim Integrated Products 功能描述:
DS1386P 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:RAMified Watchdog Timekeeper
DS1386P08-120 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:RAMified Watchdog Timekeeper