参数资料
型号: DS1391U-33+T&R
厂商: Maxim Integrated Products
文件页数: 13/26页
文件大小: 0K
描述: IC RTC W/CHARGER 10-USOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 3,000
类型: 时钟/日历
特点: 警报器,闰年,方波输出,涓流充电器
时间格式: HH:MM:SS:hh(12/24 小时)
数据格式: YY-MM-DD-dd
接口: SPI
电源电压: 2.97 V ~ 5.5 V
电压 - 电源,电池: 1.3 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-µMAX
包装: 带卷 (TR)
DS1390–DS1394
Low-Voltage SPI/3-Wire RTCs with
Trickle Charger
20
Maxim Integrated
SPI Serial-Data Bus
The DS1390/DS1391/DS1394 provide a 4-wire SPI seri-
al-data bus to communicate in systems with an SPI host
controller. The DS1390/DS1391 support SPI modes 1
and 3, while the DS1394 supports SPI modes 0 and 2.
Both devices support single-byte and multiple-byte
data transfers for maximum flexibility. The DIN and
DOUT pins are the serial-data input and output pins,
respectively. The CS input initiates and terminates a
data transfer. The SCLK pin synchronizes data move-
ment between the master (microcontroller) and the
slave (DS1390/DS1391) devices. The shift clock
(SCLK), which is generated by the microcontroller, is
active only during address and data transfer to any
device on the SPI bus. Input data (DIN) is latched on
the internal strobe edge and output data (DOUT) is
shifted out on the shift edge (Figure 9). There is one
clock for each bit transferred. Address and data bits
are transferred in groups of eight.
Address and data bytes are shifted MSB first into the
serial-data input (DIN) and out of the serial-data output
(DOUT). Any transfer requires the address of the byte
to specify a write or read, followed by one or more
bytes of data. Data is transferred out of the DOUT pin
for a read operation and into the DIN for a write opera-
tion (Figures 10 and 11).
The address byte is always the first byte entered after
CS is driven low. The most significant bit (W/R) of this
byte determines if a read or write takes place. If W/R is
0, one or more read cycles occur. If W/R is 1, one or
more write cycles occur.
Data transfers can occur one byte at a time or in multi-
ple-byte burst mode. After CS is driven low, an address
is written to the DS1390/DS1391/DS1394. After the
address, one or more data bytes can be written or
read. For a single-byte transfer, one byte is read or writ-
ten and then CS is driven high. For a multiple-byte
transfer, however, multiple bytes can be read or written
after the address has been written. Each read or write
cycle causes the RTC register address to automatically
increment. Incrementing continues until the device is
disabled. The address wraps to 00h after incrementing
to 0Fh (during a read) and wraps to 80h after incre-
menting to 8Fh (during a write). Note, however, that an
updated copy of the time is only loaded into the user-
accessible copy upon the falling edge of CS. Reading
the RTC registers in a continuous loop does not show
the time advancing.
CPHA = 0
CPHA = 1
CS
SHIFT DATA OUT (READ)
MODE 0
MODE 2
DATA LATCH/SAMPLE (WRITE)
SCLK WHEN CPOL = 0
SHIFT DATA OUT (READ)
DATA LATCH/SAMPLE (WRITE)
MODE 1
MODE 3
SHIFT DATA OUT (READ)
DATA LATCH/SAMPLE (WRITE)
SHIFT DATA OUT (READ)
SCLK WHEN CPOL = 1
Figure 9. Serial Clock as a Function of Microcontroller Clock-Polarity Bit
相关PDF资料
PDF描述
VI-J6X-MZ CONVERTER MOD DC/DC 5.2V 25W
DS1391U-3+T&R IC RTC W/CHARGER 10-USOP
ISL23415UFRUZ-T7A IC DGTL POT 256POS 50K 10TQFN
DS1374U-33+T&R IC RTC I2C W/CHARGER 10-USOP
DS1374U-3+T&R IC RTC I2C W/CHARGER 10-USOP
相关代理商/技术参数
参数描述
DS1392 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage SPI/3-Wire RTCs with Trickle Charger
DS1392U+18 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 10USOP - Bulk
DS1392U+3 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 10USOP - Bulk
DS1392U+33 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 10USOP - Bulk
DS1392U-18 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 10USOP - Bulk