- 您现在的位置：买卖IC网 > PDF目录258064 > DS1501-9ERD1TB1 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | DS1501-9ERD1TB1 |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE S02, MODULE |
| 文件页数： | 4/31页 |
| 文件大小： | 633K |
| 代理商： | DS1501-9ERD1TB1 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Cassette Style
100 Watt DC-DC Converters
S Series
Edition 1/01.2000
12/31
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Output Voltage Regulation of Single or Double Output
Modules with Outputs 1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig.8
Uo1 vs. Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note: Parallel connection of double output units should al-
ways include both, main and second output to maintain
good regulation of both outputs.
Not more than 5 units should be connected in parallel.
Series connection of second outputs without involving their
main outputs should be avoided as regulation may be poor.
The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1501-9ERD3TB2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| DS1501-9PB2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| DS1501-9PD3 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| DS1601-7EPD1TB1 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| DS1601-7EPD5T | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1501-DS1511 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Y2K-Compliant Watchdog Real-Time Clocks |
| DS1501W | 功能描述:IC RTC WDOG Y2KC 3.3V 28-DIP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 实时时钟 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 类型:时钟/日历 特点:警报器，闰年，SRAM 存储容量:- 时间格式:HH:MM:SS（12/24 小时） 数据格式:YY-MM-DD-dd 接口:SPI 电源电压:2 V ~ 5.5 V 电压 - 电源，电池:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN EP 包装:管件 |
| DS1501W+ | 功能描述:实时时钟 Y2K-Compliant Watchdog RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1501WE | 功能描述:实时时钟 Y2K-Compliant Watchdog RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1501WE/T&R | 制造商:Maxim Integrated Products 功能描述:IC RTC WDOG Y2KC 3.3V 28-TSOP |
发布紧急采购，3分钟左右您将得到回复。