参数资料
型号: DS1620S/T&R
厂商: Maxim Integrated
文件页数: 5/12页
文件大小: 0K
描述: IC THERMOMETER/STAT DIG 8-SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,000
功能: 温度计,恒温计
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±2°C(最小值)
拓扑: 比较器,寄存器库
输出类型: 数字
输出警报:
输出风扇:
电源电压: 2.7 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.209",5.30mm 宽)
供应商设备封装: 8-SO
包装: 带卷 (TR)
DS1620
THERMOSTAT OUTPUT OPERATION Figure 3
T HIGH
T LOW
T COM
TL
TH
T(°C)
OPERATION AND CONTROL
The DS1620 must have temperature settings resident in the TH and TL registers for thermostatic
operation. A configuration/status register also determines the method of operation that the DS1620 will
use in a particular application and indicates the status of the temperature conversion operation. The
configuration register is defined as follows:
CONFIGURATION/STATUS REGISTER
DONE
THF
TLF
NVB
1
0
CPU
1SHOT
where
DONE = Conversion Done Bit. 1=conversion complete, 0=conversion in progress. The power-up/POR
state is a 1.
THF = Temperature High Flag. This bit will be set to 1 when the temperature is greater than or equal
to the value of TH. It will remain 1 until reset by writing 0 into this location or by removing power from
the device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures above TH while power has been applied. The power-up/POR state is a 0.
TLF = Temperature Low Flag. This bit will be set to 1 when the temperature is less than or equal to
the value of TL. It will remain 1 until reset by writing 0 into this location or by removing power from the
device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures below TL while power has been applied. The power-up/POR state is a 0.
NVB = Nonvolatile Memory Busy Flag. 1=write to an E 2 memory cell in progress. 0=nonvolatile
memory is not busy. A copy to E 2 may take up to 10 ms. The power-up/POR state is a 0.
CPU = CPU Use Bit. If CPU=0, the CLK/ CONV pin acts as a conversion start control, when RST is
low. If CPU is 1, the DS1620 will be used with a CPU communicating to it over the 3–wire port, and the
operation of the CLK/ CONV pin is as a normal clock in concert with DQ and RST . This bit is stored in
nonvolatile E 2 memory, capable of at least 50,000 writes. The DS1620 is shipped with CPU=0.
5 of 12
相关PDF资料
PDF描述
GCM06DRTF-S13 CONN EDGECARD 12POS .156 EXTEND
EP2S30F672C4N IC STRATIX II FPGA 30K 672-FBGA
EMM44DRXI CONN EDGECARD 88POS DIP .156 SLD
VI-272-CW-F3 CONVERTER MOD DC/DC 15V 100W
ABM44DRYI CONN EDGECARD 88POS DIP .156 SLD
相关代理商/技术参数
参数描述
DS1621 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621+ 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621C 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621C-A7-W 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621S 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor