参数资料
型号: DS1621
厂商: Maxim Integrated
文件页数: 5/16页
文件大小: 337K
描述: IC THERMOMETER/STAT DIG 8-DIP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 50
功能: 温度计,恒温计
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±2°C(最小值)
拓扑: ADC(三角积分型),比较器,寄存器库
输出类型: I²C?/SMBus?
输出警报:
输出风扇:
电源电压: 2.7 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 通孔
封装/外壳: 8-DIP(0.300",7.62mm)
供应商设备封装: 8-DIP
包装: 管件
DS1621
 
5 of 16
In one-shot mode, the DS1621 performs a single temperature conversion when a Start Convert T
command is issued. When the conversion is complete, the device enters a low-power idle state and
remains in that state until a single temperature conversion is again initiated by a Start Convert T
command.
 
Thermostat Control
In its operating mode, the DS1621 functions as a thermostat with programmable hysteresis as shown in
Figure 3. The thermostat output updates as soon as a temperature conversion is complete.
 
When the DS1621s temperature meets or exceeds the value stored in the high temperature trip register
(TH), the output becomes active and will stay active until the temperature falls below the temperature
stored in the low temperature trigger register (TL). In this way, any amount of hysteresis may be
obtained.
 
The active state for the output is programmable by the user so that an active state may either be a logic
"1" (V
DD
) or a logic "0" (0V). This is done using the POL bit in the configuration reagister as explained
in the Operation and Control section of this datasheet.
 
Figure 3. THERMOSTAT OUTPUT OPERATION 
 
DQ (Thermostat output, Active = High)
 
 
 
 
 
 
 
 
 
OPERATION AND CONTROL
The DS1621 must have temperature settings resident in the TH and TL registers for thermostatic
operation. A configuration/status register also determines the method of operation that the DS1621 will
use in a particular application, as well as indicating the status of the temperature conversion operation.
 
The configuration register is defined as follows:
 
MSb
Bit 6
Bit5
Bit 4
Bit 3
Bit 2
Bit 1
LSb
DONE
THF
TLF
NVB
X
X
POL
1SHOT
 
 
where
 
DONE  =  Conversion Done bit. 1 = Conversion complete, 0 = Conversion in progress. 
 
THF     =  Temperature High Flag. This bit will be set to 1 when the temperature is greater than or 
equal to the value of TH. It will remain 1 until reset by writing 0 into this location or removing power
from the device. This feature provides a method of determining if the DS1621 has ever been subjected to
temperatures above TH while power has been applied.
 
TL
TH
T 癈
相关PDF资料
PDF描述
NCP512SQ31T1G IC REG LDO 3.1V .2A SC70-5
HAZ470MBABF0KR CAP CER 47PF 1KV 20% RADIAL
GCM02DSEN-S13 CONN EDGECARD 4POS .156 EXTENDER
RCA14DTKN CONN EDGECARD 28POS DIP .125 SLD
HAZ470MBABD0KR CAP CER 47PF 1KV 20% RADIAL
相关代理商/技术参数
参数描述
DS1621+ 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621C 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621C-A7-W 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621S 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1621S/T&R 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER & THERMOSTAT - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC