- 您现在的位置：买卖IC网 > PDF目录97861 > DS1624 (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 13BIT(s), RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | DS1624 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 13BIT(s), RECTANGULAR, SURFACE MOUNT |
| 封装： | 0.300 INCH, DIP-8 |
| 文件页数： | 14/16页 |
| 文件大小： | 594K |
| 代理商： | DS1624 |
DS1624
7 of 16
Temperature is represented in the DS1624 in terms of a 0.03125
°C LSB, yielding the following 13–bit
format:
OPERATION AND CONTROL
A configuration/status register is used to determine the method of operation of the DS1624 will use in a
particular application as well as indicating the status of the temperature conversion operation.
The configuration register is defined as follows:
CONFIGURATION/STATUS REGISTER
where
DONE = Conversion Done bit. “1” = Conversion complete, “0” = conversion in progress.
1SHOT = One Shot Mode. If 1SHOT is “1”, the DS1624 will perform one temperature conversion upon
receipt of the Start Convert T protocol.
If 1SHOT is “0”, the DS1624 will continuously perform
temperature conversions. This bit is nonvolatile and the DS1624 is shipped with 1SHOT = “0”.
Since the configuration register is implemented in E
2, writes to the register require 10 ms to complete.
After issuing a command to write to the configuration register, no further accesses to the DS1624 should
be made for at least 10 ms.
OPERATION – MEMORY
BYTE PROGRAM MODE
In this mode, the master sends addresses and one data byte to the DS1624.
Following a START condition, the device code (4–bit), the slave address (3 bit), and the R/ W bit, which
is logic LOW, are placed onto the bus by the master. The master then sends the Access Memory protocol.
This indicates to the addressed DS1624 that a byte with a word address will follow after it has generated
an acknowledge bit. Therefore, the next byte transmitted by the master is the word address and will be
written into the address pointer of the DS1624. After receiving the acknowledge of the DS1624, the
master device transmits the data word to be written into the addressed memory location. The DS1624
acknowledges again and the master generates a STOP condition. This initiates the internal programming
cycle of the DS1624. A repeated START condition, instead of a STOP condition, will abort the
programming operation.
During the programming cycle the DS1624 will not acknowledge any further accesses to the device until
the programming cycle is complete (approximately 10 ms.)
0
1
0
1
0
1
0
1
0
LSB
= +25.0625°C
MSB
DONE
1
0
1
0
1
1SHOT
相关PDF资料 |
PDF描述 |
|---|---|
| DS1626S+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1629S | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| DS1631S+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1631AU | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT |
| DS1631 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1624+ | 功能描述:板上安装温度传感器 Digital Thermometer & Memory RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1624S | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1624S/T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR W/MEMORY 8P SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM/EEPROM DIG 256BYT 8SOIC |
| DS1624S/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1624S+ | 功能描述:板上安装温度传感器 Digital Thermometer & Memory RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。