- 您现在的位置：买卖IC网 > Datasheet目录39 > DS1626S+ (Maxim Integrated)IC THERMOMETER/STAT DIG 8-SOIC Datasheet资料下载
参数资料
| 型号： | DS1626S+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/12页 |
| 文件大小： | 141K |
| 描述： | IC THERMOMETER/STAT DIG 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | 3 线串行 |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
DS1626/DS1726
8 of 12
CPU BIT AND STAND-ALONE THERMOSTAT OPERATION
In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without requiring
a microcontroller to start/stop temperature conversions. The CPU bit in the configuration register
determines if stand-alone mode is enabled.
When CPU = 1 stand-alone mode is disabled, and the only way to start/stop temperature conversions is
by using a microcontroller to transmit Start Convert T and Stop Convert T commands, respectively.
Stand-alone mode is enabled when CPU = 0. In this mode, when RST = 0 the CLK/CNV pin operates as
a control signal to start and stop temperature measurements. Driving CLK/CNV low initiates continuous
temperature conversions that will continue until CLK/CNV is brought high again. If the CLK/CNV pin is
driven low and then returned to a high state in less than 10ms, only one temperature conversion will be
performed after which the DS1626/DS1726 will return to a low-power idle state (i.e., one-shot operation).
Note that when stand-alone mode is enabled, the 1SHOT bit in the configuration register is ignored, and
only the CLK/CNV signal determines whether continuous or one-shot conversions take place.
Since T
H
, T
L
, and the CPU bit are stored in EEPROM, the DS1626/DS1726 can be preprogrammed for
stand-alone operation. If desired, the CLK/CNV and RST pin can be connected to GND so the
DS1626/DS1726 will automatically begin taking temperature measurements at power-up
Normal bus communication with the DS1626/DS1726 can still take place in stand-alone mode when
RST = 1. When communication is initiated, stand-alone conversions are automatically halted. If during
the bus communication continuous temperature conversions are started using the Start Convert T
command, they can only be stopped by issuing a Stop Convert T command.
Figure 5. THERMOSTAT OUTPUT OPERATION
T
L
T
H
TEMP
LOGIC 0
LOGIC 1
T
COM
TEMP
LOGIC 0
LOGIC 1
T
HIGH
TEMP
LOGIC 0
LOGIC 1
T
LOW
相关PDF资料 |
PDF描述 |
|---|---|
| DS1629S+T&R | IC THERM/RTC/CALENDAR DIG 8-SOIC |
| DS1631S+T&R | IC THERMOMETER DIG HI-PREC 8SOIC |
| DS1721U+T&R | IC THERMOMETER/STAT DIG HP 8USOP |
| DS1722S | IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1775R7+T&R | IC THERMOM/STAT DIG 111 SOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1626S+ | 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1626S+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC |
| DS1626S+T&R | 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1626U | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1626U/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 3-WIRE DIG THERM (USOP) T&R - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。