- 您现在的位置：买卖IC网 > PDF目录19366 > DS1626U+T&R (Maxim Integrated)IC THERMOMETER/STAT DIG 8-USOP PDF资料下载
参数资料
| 型号： | DS1626U+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/12页 |
| 文件大小： | 141K |
| 描述： | IC THERMOMETER/STAT DIG 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | 3 线串行 |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS1626/DS1726
10 of 12
Table 4. RESOLUTION CONFIGURATION
R1
R0
RESOLUTION
(BITS)
CONVERSION
TIME (MAX)
(ms)
0
0
9
93.75
0
1
10
187.5
1
0
11
375
1
1
12
750
3-WIRE SERIAL DATA BUS
The 3-wire bus consists of three signals: RST (active-low reset), CLK (clock), and DQ (data). 3-wire
communication is controlled by the RST signal, which functions as chip select signal. All data is
transferred LSb first over the 3-wire bus. All communication with the DS1626/DS1726 is initiated by
driving RST high. Driving RST low terminates communications and causes DQ to go to a high-
impedance state. Note that RST must be toggled low after every communication sequence to ensure that
subsequent commands are recognized by the DS1626/DS1726.
When writing to the DS1626/DS1726, data must be valid during the rising edge of CLK. During read
operations the DS1626/DS1726 output data on DQ on the falling edge of CLK and the data remains valid
through the following rising edge, at which time the DQ pin becomes high impedance until the next
falling edge.
To communicate with the DS1626/DS1726, the master must first drive RST high and then begin
generating the CLK signal while transmitting the desired DS1626/DS1726 command byte. If the
command is a Start Convert T, Stop Convert T, or Software POR command, the transaction is finished
when the last bit of the command has been sent. Figure 7a illustrates a Start Convert T command
sequence.
When writing to the DS1626/DS1726, the master must begin transmitting data during the clock cycle
immediately following the command byte. The DS1626/DS1726 will save only the number of data bits
needed for the specific transaction. For example, for the Write TH or Write TL commands, after twelve
bits of data have been transmitted by the master, the DS1626/DS1726 will ignore any subsequent data
transmitted before RST goes low. Thus, if data is being transmitted in byte-length segments, the
DS1626/DS1726 will load the first twelve bits into the T
H
/T
L
register, and the next four bits will be
ignored. On the other hand, it is necessary to transmit at least the required number of bits for the
requested transaction (i.e., 12-bits to T
H
/T
L
or 8-bits to the configuration register), because the
DS1626/DS1726 will not save data until the expected number of bits have been received. Write TH and
Write TL sequences are illustrated in Figure 7b and a Write Config sequence is shown in Figure 7c. Note
that these figures assume byte-wide data transfers.
When reading data from the DS1626/DS1726, the DS1626/DS1726 will begin sending data during the
clock cycle immediately following the command byte. After the last data byte has been sent, the
DS1626/DS1726 will transmit a 0 during each subsequent clock until RST goes low. Figure 7d illustrates
a Read Temperature sequence and a Read Config transaction is shown in Figure 7e. The sequence for
reading the T
H
or T
L
registers is the same as the Read Temp transaction in Figure 7d except that the Read
TH or Read TL command is used.
相关PDF资料 |
PDF描述 |
|---|---|
| 3-1624113-0 | INDUCTOR 12NH 5% 0805 |
| VI-B4Y-CY-F2 | CONVERTER MOD DC/DC 3.3V 33W |
| TAJY476M016RNJ | CAP TANT 47UF 16V 20% 2917 |
| VI-B4Y-CX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VE-BTF-CV-F3 | CONVERTER MOD DC/DC 72V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1628 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Octal TRI-STATE MOS Drivers |
| DS1628J | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Octal TRI-STATE MOS Drivers |
| DS1628J/A+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Memory Driver |
| DS1629 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:2-Wire Digital Thermometer and Real Time Clock |
| DS1629S | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。