- 您现在的位置：买卖IC网 > PDF目录21988 > DS1631Z/T&R (Maxim Integrated)IC THERMOMETER DIG HI-PREC 8SOIC PDF资料下载
参数资料
| 型号： | DS1631Z/T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 13/16页 |
| 文件大小： | 435K |
| 描述： | IC THERMOMETER DIG HI-PREC 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
DS1631/DS1631A/DS1731
13 of 15
2-WIRE READS
The master can read data from the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH,
Access TL, or Read Temperature command following the control byte (see Figures 9c and 9e). After
receiving an ACK in response to the command, the master must generate a repeated START followed by
a control byte with the same slave address as the first control byte. However, this time the R/W?/SPAN>?/SPAN> bit must
be a 1, which tells the DS1631/DS1631A/DS1731 that a read is being performed. After the
DS1631/DS1631A/DS1731 send an ACK in response to this control byte, it begins transmitting the
requested data on the next clock cycle. One byte of data will be transmitted when reading from the
configuration register after which the master must respond with a NACK followed by a STOP. For two-
byte reads (i.e., from the Temperature, T
H
, or T
L
register), the master must respond to the first data byte
with an ACK and to the second byte with a NACK followed by a STOP. If only the most significant byte
of data is needed, the master can issue a NACK followed by a STOP after reading the first data byte.
COMMAND SET
The DS1631/DS1631A/DS1731 command set is detailed below:
Start Convert T [ 51h ]
Initiates temperature conversions. If the part is in one-shot mode (1SHOT = 1), only one conversion is
performed. In continuous mode (1SHOT = 0), continuous temperature conversions are performed until a
Stop Convert T command is issued.
Stop Convert T [ 22h ]
Stops temperature conversions when the device is in continuous conversion mode (1SHOT = 0).
Read Temperature [ AAh ]
Reads last converted temperature value from the 2-byte temperature register.
Access TH [ A1h ]
Reads or writes the 2-byte T
H
register.
Access TL [ A2h ]
Reads or writes the 2-byte T
L
register.
Access Config [ ACh ]
Reads or writes the 1-byte configuration register.
Software POR [ 54h ]
Initiates a software power-on-reset (POR), which stops temperature conversions and resets all registers
and logic to their power-up states. The software POR allows the user to simulate cycling the power
without actually powering down the device.
相关PDF资料 |
PDF描述 |
|---|---|
| VJ1206A221KBCAT4X | CAP CER 220PF 200V 10% NP0 1206 |
| 2-1879023-3 | INDUCTOR .27UH 5% 1008 |
| DA7W2P500P00LF | DSUB POWER STB 7W2 PIN |
| VJ1206A331JBCAT4X | CAP CER 330PF 200V 5% NP0 1206 |
| 1-1879023-9 | INDUCTOR .15UH 5% 1008 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1632 | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1632 WAF | 制造商:Rochester Electronics LLC 功能描述: |
| DS1632 WAF UP | 制造商:Rochester Electronics LLC 功能描述: |
| DS1632+ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1632A6B_BAA WAF | 制造商:Rochester Electronics LLC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。