- 您现在的位置：买卖IC网 > PDF目录16676 > DS1632S (Maxim Integrated Products)IC CTRLR PC PWR FAIL/RSET 16SOIC PDF资料下载
参数资料
| 型号： | DS1632S |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PC PWR FAIL/RSET 16SOIC |
| 标准包装： | 45 |
| 应用： | PC 电源故障与复位控制器 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 500µA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
DS1632
OPERATION – POWER-FAIL, BATTERY BACKUP
The DS1632 provides a switch to direct power from the battery (V BAT ) or the incoming supply (V CC ),
depending on which is greater. This switch has a voltage drop of less than 0.3 volts. The V CC input is
constantly monitored by a precision comparator for an out-of-tolerance condition. When such a condition
occurs, the power-fail signals are driven to their active state immediately. The reset signals are also driven
active, but this action is delayed by a time determined by the level of the input on the reset duration pin
(RD). If RD is tied to ground then reset signals will become active after 9 ms. If RD is tied to V CC , then
reset signals will become active after 18 ms. Once active, both the reset signals and the power-fail signals
will remain active as long as a (V CC ) out-of-tolerance condition persists. If an out-of-tolerance condition
is not long enough to activate the reset signals, then only the power-fail signals would be affected. When
power returns to within nominal limits the power-fail signals will return immediately to the inactive state.
However, the reset signals remain in the active state for a time which is dependent on the state of the RD
pin. If RD is tied to ground, the reset signals will remain active for 95 ms. If RD is tied to V CC , then the
reset signals will remain active for 190 ms after power is within nominal limits. The delay action on the
reset signals allows time for the power supply and microprocessor clock oscillators to stabilize. The
tolerance pin (TOL) selects the point at which power-fail detection occurs. With the tolerance pin
grounded, power-fail detection occurs in the range of 4.75V to 4.5V. If the tolerance pin is connected to
V CC , then power-fail detection occurs in the range of 4.5V to 4.25V. During most power supply
conditions the V CC input will supply power to all functions within the chip and also to the V CCO pin. The
battery pin (V BAT ) only supplies power when V CC is less than V BAT . When V CC is below the level of V BAT
only the V CCO and the OSC OUT pin remain powered by V BAT . All other outputs will be driven to ground
when in a logic low state and will be driven to V CC when in a logic high state. This is done to preserve
battery capacity by avoiding battery drain resulting from loads on these outputs. The output ground level
will be maintained for all levels of V CC , even V CC = GND. However, the output V CC level will be
maintained only for V CC > 2.0V. Internal battery power consumption is less than 2 m A while V BAT is
supplying power. The external load on OSC OUT and V CCO must be added to internal consumption to
determine the total load on the battery.
OPERATION - PUSHBUTTON RESET
The DS1632 provides an input pin for direct connection to a pushbutton. The pushbutton reset input
PBRST requires an active low level input. While TTL levels are sufficient to properly activate this input,
it has been primarily designed for contact closure. Internally, this input is debounced and timed such that
RST and RST signals of 95ms or 190 ms minimum are generated. If RD is tied to ground, then a reset
pulse of 95 ms is generated. If RD is tied to V CC then a reset pulse of 190 ms is generated. The delay time
is started as the pushbutton reset input is released from low level.
OPERATION - LOW BATTERY WARNING
The DS1632 provides outputs which warn of a low battery condition. Whenever V CC is within nominal
limits, the V BAT input is continuously monitored. If the V BAT input is out of tolerance, the low battery
outputs are driven to their active states, and will remain in the active state as long as V CC is within
nominal limits or until the battery input is restored to an in limit status. On power-up, if the V BAT input is
out of tolerance, the low battery outputs are not guaranteed active until power-fail is deactivated, but
guaranteed active prior to reset inactive. When V CC is below the V CC fail trip point both LB and LB will
be driven to ground.
For application information, please reference Application Note 64, published separately.
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| GEC36DRAN | CONN EDGECARD 72POS R/A .100 SLD |
| HMC07DRTH-S13 | CONN EDGECARD 14POS .100 EXTEND |
| VE-BWM-EX | CONVERTER MOD DC/DC 10V 75W |
| TC642BEUA | IC PWM FAN SPEED CTRLR 8-MSOP |
| TC647BEOA | IC PWM FAN SPEED CTRLR 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1632S/T&R | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1632S+ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1632S+T&R | 制造商:Maxim Integrated Products 功能描述:IC POWER FAIL W/RESET 16SOIC |
| DS1632S+T&R | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1632SN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Power Supply Supervisor |
发布紧急采购，3分钟左右您将得到回复。