参数资料
| 型号： | DS1666S-10+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC DIG POT 10K 16SOIC |
| 标准包装： | 45 |
| 接片： | 128 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 3 线串行（芯片选择，递增，增/减） |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
DS1666
3 of 9
102899
PIN DESCRIPTIONS
VCC - Power Supply. The DS1666 will support supply voltages ranging from +4.5 to +5.5 volts.
GND -
Ground Terminal.
VB - Negative Bias. The DS1666 will support a negative bias ranging from 0 to -5 volts.
H -
High-Terminal of Potentiometer. It is not required that this terminal be connected to a potential
greater than the VL terminal. Voltage applied to the VH terminal can not exceed the power-supply
voltage, (VCC), or go below the negative bias, (VB).
VL - Low-Terminal of Potentiometer. It is not required that this terminal be connected to a potential less
than the VH terminal. Voltage applied to the VL terminal cannot exceed the power-supply voltage, (VCC),
or go below the negative bias (VB).
VW - Wiper of the Potentiometer. Its position on the resistor array is controlled by the 3-terminal control
port. Voltage applied to the wiper cannot exceed the power-supply voltage, VCC, or go below the
negative bias (VB).
CS
-
Chip Select. The CS input is used to activate the control port of the DS1666. This input is active
low. When in a high-state, activity on the INC and U/ D port pins will not affect or change wiper
position.
INC
-
Wiper Movement Control. This input provides for wiper position changes when the CS pin is low.
Wiper position changes will occur one position per high-to-low transition of this input signal. Position
changes will not occur if the CS pin is in a high-state.
U/ D -
Up/Down Control. This input sets the direction of wiper movement. When in a high-state and CS
is low, any high-to-low transition on INC will cause a one position movement of the wiper towards the
VH terminal. When in a low-state and CS is low, any high-to-low transitions on INC will cause the
position of the wiper to move towards the VL terminal.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1666S-10 | IC DIG POT 10K 16SOIC |
| DS1803Z-010 | IC POT DUAL ADDRESS 10K 16-SOIC |
| DS1803Z-050 | IC POT DUAL ADDRESS 50K 16-SOIC |
| MS3122E14-15P | CONN RCPT 15POS BOX MNT W/PINS |
| ICS180MI-01LF | IC CLOCK GEN LOW EMI 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1666S-10/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC DIG POT 10K 16SOIC |
| DS1666S-10/T&R | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1666S-10+ | 功能描述:数字电位计 IC 5V+/- Pseudo Log Audio RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1666S-10+T&R | 制造商:Maxim Integrated Products 功能描述:IC DIG POT 10K 16SOIC |
| DS1666S-10+T&R | 功能描述:数字电位计 IC 5V+/- Pseudo Log Audio RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。