- 您现在的位置：买卖IC网 > PDF目录1994 > DS1685EN-5/T&R (Maxim Integrated Products)IC RTC 5V 64BIT Y2K IND 24TSSOP PDF资料下载
参数资料
| 型号： | DS1685EN-5/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/34页 |
| 文件大小： | 0K |
| 描述： | IC RTC 5V 64BIT Y2K IND 24TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，NVSRAM，方波输出，Y2K |
| 存储容量： | 242B |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | 并联 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电压 - 电源，电池： | 2.5 V ~ 3.7 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
DS1685/DS1687 3V/5V Real-Time Clocks
14 of 34
NV RAM—RTC
The 242 general-purpose NV RAM bytes are not dedicated to any special function within the DS1685/DS1687.
They can be used by the application program as nonvolatile memory and are fully available during the update
cycle.
The user RAM is divided into two separate memory banks. When the bank 0 is selected, the 14 RTC registers and
114 bytes of user RAM are accessible. When bank 1 is selected, an additional 128 bytes of user RAM are
accessible through the extended RAM address and data registers.
INTERRUPT CONTROL
The DS1685/DS1687 includes six separate, fully automatic sources of interrupt for a processor:
1) Alarm Interrupt
2) Periodic Interrupt
3) Update-Ended Interrupt
4) Wake-Up Interrupt
5) Kickstart Interrupt
6) RAM Clear Interrupt
The conditions that generate each of these independent interrupt conditions are described in detail in other
sections of this text. This section describes the overall control of the interrupts.
The application software can select which interrupts, if any, are to be used. There are a total of 6 bits, including 3
bits in Register B and 3 bits in Extended Register 4B, that enable the interrupts. The extended register locations
are described later. Writing a logic 1 to an interrupt-enable bit permits that interrupt to be initiated when the event
occurs. A logic 0 in the interrupt enable bit prohibits the IRQ pin from being asserted from that interrupt condition. If
an interrupt flag is already set when an interrupt is enabled, IRQ is immediately set at an active level, even though
the event initiating the interrupt condition might have occurred much earlier. As a result, there are cases where the
software should clear these earlier generated interrupts before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is set to a logic 1 in Register C or in Extended Register 4A.
These flag bits are set regardless of the setting of the corresponding enable bit located either in Register B or in
Extended Register 4B. The flag bits can be used in a polling mode without enabling the corresponding enable bits.
However, care should be taken when using the flag bits of Register C as they are automatically cleared to 0
immediately after they are read. Double latching is implemented on these bits so that set bits remain stable
throughout the read cycle. All bits that were set are cleared when read and new interrupts that are pending during
the read cycle are held until after the cycle is completed. One, two, or three bits can be set when reading Register
C. Each used flag bit should be examined when read to ensure that no interrupts are lost.
The flag bits in Extended Register 4A are not automatically cleared following a read. Instead, each flag bit can be
cleared to 0 only by writing 0 to that bit.
When using the flag bits with fully enabled interrupts, the IRQ line is driven low when an interrupt flag bit is set and
its corresponding enable bit is also set. IRQ is held low as long as at least one of the six possible interrupt sources
has its flag and enable bits both set. The IRQF bit in Register C is a 1 whenever the IRQ pin is being driven low as
a result of one of the six possible active sources. Therefore, determination that the DS1685/DS1687 initiated an
interrupt is accomplished by reading Register C and finding IRQF = 1. IRQF remains set until all enabled interrupt
flag bits are cleared to 0.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1688S+ | IC RTC W/NV RAM CTRL 28-SOIC |
| DS1689SN+T&R | IC RTC SER NV RAM CTRL IN 28SOIC |
| DS17285S-3NT | IC RTC 3V 2K NV RAM 24-SOIC |
| DS1742-100IND | IC RTC RAM Y2K 5V 100NS 24-EDIP |
| DS1743P-70+ | IC RTC RAM Y2K 5V 70NS 34-PCM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1685N-3 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Real-Time Clock |
| DS1685N-5 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Real-Time Clock |
| DS1685Q-3 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1685Q-3/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS1685Q-3/TR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:3V/5V Real-Time Clocks |
发布紧急采购，3分钟左右您将得到回复。