- 您现在的位置：买卖IC网 > PDF目录97864 > DS1775R1 (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | DS1775R1 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | LEAD FREE, SOT-23, 5 PIN |
| 文件页数： | 15/17页 |
| 文件大小： | 408K |
| 代理商： | DS1775R1 |
DS1775
7 of 14
register. The pointer address must always proceed data in writing to a register, regardless of which
address is currently selected. Please refer to the “2–Wire Serial Data Bus” section for details of the 2–
wire bus protocol.
Configuration Register Programming
The configuration register is accessed if the DS1775 pointer is currently set to the 01h location. Writing
to or reading from the register is determined by the R/W bit of the 2–wire control byte (See “2–wire
Serial Data Bus” section). Data is read from or written to the configuration register MSb first. The format
of the register is illustrated below in Figure 3. The effect each bit has on DS1775 functionality is
described below along with the power–up state of the bit. The user has read/write access to all bits in the
configuration register. The entire register is volatile, and thus it will power–up in the default state.
Configuration/Status Register Figure 3
0
R1
R0
F1
F0
POL
TM
SD
MSb
LSb
SD = Shutdown bit. If SD is “0”, the DS1775 will continuously perform temperature conversions and
store the last completed result in the thermometer register. If SD is changed to “1”, the conversion in
progress will be completed and stored; then the device will revert to a low–power standby mode. The
O.S. output will be cleared if the device is in the interrupt mode and remain unchanged in the comparator
mode. The 2–wire port remains active. The power–up default state is “0” (continuous conversion mode).
TM = Thermostat mode. If TM=“0”, the DS1775 is in the comparator mode. TM=“1” sets the device to
the interrupt mode. See “OPERATION–Thermostat Control” section for a description of the difference
between the two modes. The power–up default state of the TM bit is “0” (comparator mode).
POL = O.S. Polarity Bit. If POL = “1”, the active state of the O.S. output will be high. A “0” stored in
this location sets the thermostat output to an active low state. The user has read/write access to the POL
bit, and the power–up default state is “0” (active low).
F0, F1 = O.S. Fault Tolerance bits. The fault tolerance defines the number of consecutive conversions
returning a temperature beyond limits is required to set the O.S. output in an active state. This may be
necessary to add margin in noisy environments. Table 4 below defines the four settings. The DS1775 will
power up with F0=F1=“0”, such that a single occurrence will trigger a fault.
Fault Tolerance Configuration Table 4
F1
F0
Consecutive conversions beyond limits to generate fault
0
1
0
1
2
1
0
4
1
6
R0, R1 = Thermometer resolution bits. Table 5 defines the resolution of the digital thermometer, based
on the settings of these two bits. There is a direct trade-off between resolution and conversion time, as
depicted in the AC Electrical Characteristics. The default state is R0="0" and R1="0" (9–bit conversions).
相关PDF资料 |
PDF描述 |
|---|---|
| DS1775R2 | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1775R3 | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1775R4 | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1775R1&R | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1775R5 | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1775R1/T&R | 制造商:Maxim Integrated Products 功能描述:DS1775R DIG THERM T&R 001 ADD SOT23 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOM/STAT DIG 001 SOT-23-5 |
| DS1775R1/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1775R1+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 5PIN SOT-23 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOM/STAT DIG 001 SOT-23-5 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital Thermometer & Thermostat |
| DS1775R1+T&R | 功能描述:板上安装温度传感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1775R1+U | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。