- 您现在的位置：买卖IC网 > PDF目录9060 > DS1804-100 (Maxim Integrated Products)IC POT TRIMMER NV 100K 8-DIP PDF资料下载
参数资料
| 型号： | DS1804-100 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC POT TRIMMER NV 100K 8-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 接片： | 100 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 3 线（芯片选择，递增，增/减） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | DS1804100 |
DS1804
6 of 10
NOTES:
1) All voltages are referenced to ground.
2) Valid for VCC = 5V only.
3) Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4) Maximum current specifications are based on the clock rate of INC input. This specification
represents the current required when changing the wiper position.
5) Standby current levels apply when all inputs are driven to appropriate supply levels. CS , INC , U/ D =
VCC.
6) Wiper load time is specified as the time required for the DS1804 to load the wiper position with the
contents of nonvolatile memory once VCC has reached a stable operating voltage equal to or greater
than 2.7V.
7) The DS1804 is available in three resistor values. These include the DS1804-010, 10k
; the DS1804-
050, 50k
; and the DS1804-100, 100k.
8) Valid at TA = +25°C only.
9) Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1804 is specified to provide an absolute linearity of ±0.60 LSB.
10) Relative linearity is used to determined the change in voltage between successive tap positions. The
DS1804 is specified to provide a relative linearity specification of ±0.25 LSB.
11) -3dB cutoff frequency characteristics for the DS1804 depend on potentiometer total resistance.
DS1804-010, 1MHz; DS1804-050, 200kHz; and DS1804-100, 100kHz.
12) Capacitance values apply at TA = +25°C.
13) See Figure 2.
14) Power-up time is specified as the time required before the three-terminal control becomes active after
a stable power supply level has been reached.
15) At VCC = 2.7V, VIL = 0.8V.
16) The INC low to CS inactive is specified to be 50ns minimum. This is the transition condition which
allows the DS1804 three-terminal port to become inactive without writing the EEPROM memory of
the part.
17) Wiper Storage Time, tWST, is the time require for the DS1804 to write EEPROM memory for storage
of a new wiper position. The maximum time required to accomplish this task is specified at 10ms.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-25Y-MX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| DS1804-010 | IC POT TRIMMER NV 10K 8-DIP |
| DS1669-10 | IC RHEOSTAT DALLASTAT 10K 8-DIP |
| VI-25Y-MX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| DS1845E-010 | IC POT/MEM DUAL NV 10K 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1804-100+ | 功能描述:数字电位计 IC NV Trimmer RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1804-50 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:IC-NON VOLATILE POT |
| DS1804C | 制造商:NANOTRON TECHNOLOGIES 功能描述:IC DELAY LINE CDDL 1804 |
| DS1804NZ-100 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1804U010 | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。