- 您现在的位置：买卖IC网 > PDF目录9173 > DS1807E+T&R (Maxim Integrated Products)IC POT ADDRESS 2X AUDIO 14-TSSOP PDF资料下载
参数资料
| 型号： | DS1807E+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC POT ADDRESS 2X AUDIO 14-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 接片： | 64 + 静音 |
| 电阻（欧姆）： | 45k |
| 电路数： | 2 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
DS1807
7 of 13
110499
When the master has received the ACKNOWLEDGE from the DS1807, the master can then begin to
receive potentiometer wiper data. The value of the potentiometer-0 wiper position will be the first
returned from the DS1807. Once the 8 bits of the potentiometer-0 wiper position have been transmitted,
the master will need to issue an ACKNOWLEDGE, unless it is the only byte to be read, in which case the
master issues a NOT ACKNOWLEDGE. If desired the master may stop the communication transfer at
this point by issuing the STOP condition. However, if the value of the potentiometer-1 wiper position
value is needed communication transfer can continue by clocking the remaining eight bits of the
potentiometer-1 value, followed by a NOT ACKNOWLEDGE. Final communication transfer is
terminated by issuing the STOP command. Again the flow of the read operation is presented in Figure 6.
WRITING THE DS1807
A data flow diagram for writing the DS1807 is shown in Figure 7. The DS1807 has three commands
which are used to change the position(s) of the wiper. These include write pot-0, write pot-1, and write
pot-0/1. The write pot-0 command allows the user to write the value of potentiometer-0 and as an option
the value of potentiometer-1. The write-1 command allows the user to write the value of potentiometer-1
only. The last write command, write-0/1, allows the user to write both potentiometers to the same value
with one command and one data value being issued.
All the write operations begin with a START condition. Following the START condition, the master
device will issue the control byte. The read/write bit of the control byte will be set to 0 for writing the
DS1807. Once the control byte has been issued and the master receives the acknowledgment from the
DS1807, the command byte is transmitted to the DS1807. As mentioned above, there exist three write
operations that can be used with the DS1807. The binary value of each write command is shown in Figure
7 and also in Table 1.
2-WIRE WRITE COMMAND WORDS Table 1
COMMAND
COMMAND VALUE
Write Potentiometer-0
101010 01
Write Potentiometer-1
101010 10
Write Both Pots
101011 11
Once the DS1807 has received the command byte, it will responds with an ACKNOWLEDGE. The
master can then write the corresponding data-byte associated with the command byte. When the DS1807
has received the data byte(s), it will respond with an acknowledgement. At this point the master device
should respond with the STOP condition.
ZERO-CROSSING DETECTION COMMAND WORD
Zero-crossing detection was described under the operation section of this document. As stated earlier,
zero-crossing detection must be deactivated or activated under software control. The command words
used to activate or deactivate the zero-crossing detection feature is shown in Table 2.
ZERO-CROSSING DETECTION COMMAND WORDS Table 2
COMMAND
COMMAND VALUE
Activate Zero-Crossing
101111 01
Deactivate Zero-Crossing
101111 10
相关PDF资料 |
PDF描述 |
|---|---|
| MS27466T23F53S | CONN RCPT 53POS WALL MT W/SCKT |
| DS1801E-014+T&R | IC POT DUAL AUDIO TAPER 14-TSSOP |
| 7WBD3306AMUTCG | TRANSLATOR 2BIT FST BUS SW 8UDFN |
| 7WBD3305USG | TRANSLATOR 2BIT FST BUS SW US8 |
| 7WBD3126USG | TRANSLATOR 2BIT BUS SW US8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1807N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| DS1807S | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1807S/T&R | 制造商:Maxim Integrated Products 功能描述:ADDRESABL DUAL AUDIO POT 16L SO T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT ADDRESS 2X AUDIO 16-SOIC |
| DS1807S/T&R | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1807S/TR | 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer, 16 Pin, Plastic, SOP |
发布紧急采购，3分钟左右您将得到回复。