- 您现在的位置：买卖IC网 > PDF目录15053 > DS1810-15+T&R (Maxim Integrated Products)IC ECONORESET 5V P-P 15% TO92-3 PDF资料下载
参数资料
| 型号： | DS1810-15+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | IC ECONORESET 5V P-P 15% TO92-3 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 系列： | EconoReset |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-226-3、TO-92-3（TO-226AA）成形引线 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 带卷 (TR) |
DS1810
OPERATION - POWER MONITOR
The DS1810 provides the function of detecting out-of-tolerance power supply conditions and warning a
processor-based system of impending power failure. When V CC is detected as out-of-tolerance, the RST
signal is asserted. On power-up, RST is kept active for approximately 150 ms after the power supply has
reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST
is released.
BLOCK DIAGRAM (PUSH-PULL OUTPUT) Figure 1
APPLICATION EXAMPLE Figure 2
OUTPUT VALID CONDITIONS
All versions of the DS1810 can maintain a valid output as long as V CC remains above 1.2 volt. However,
the RST outputs on the DS1810 use a push-pull structure which can maintain a valid output below 1.2
volts on an input. To sink current below 1.2 volts, a resistor can be connected from RST to Ground (see
Figure 3). This arrangement will maintain a valid value on the RST outputs even it V CC approaches 0
volts. During both power-up and -down this arrangement will draw current when RST is in the high state.
A value of about 100 k V should be adequate to maintain a valid condition.
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| H2BBG-10112-Y8-ND | JUMPER-H1501TR/A3048Y/H1501TR 12 |
| H2BBG-10112-W8-ND | JUMPER-H1501TR/A3048W/H1501TR 12 |
| LGY1V472MELZ35 | CAP ALUM 4700UF 35V 20% SNAP |
| DS1812-15+T&R | IC ECONORESET 5V P-P 15% TO92-3 |
| LGY1H332MELZ35 | CAP ALUM 3300UF 50V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1810-20 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS1810-5 | 功能描述:监控电路 5V EconoReset w/Push Pull Output RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1810-5/T&R | 制造商:Maxim Integrated Products 功能描述:ECONORESET 5V-5% CMOS OUT/TO-92 T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC ECONORESET 5V P-P 5% TO92-3 |
| DS1810-5/T&R | 功能描述:监控电路 5V EconoReset w/Push Pull Output RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1810-5+ | 功能描述:监控电路 5V EconoReset w/Push Pull Output RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。