- 您现在的位置：买卖IC网 > PDF目录258148 > DS1814CR-10T&R (DALLAS SEMICONDUCTOR) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 PDF资料下载
参数资料
| 型号： | DS1814CR-10T&R |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封装： | SOT-23, 5 PIN |
| 文件页数： | 2/8页 |
| 文件大小： | 110K |
| 代理商： | DS1814CR-10T&R |
DS1814/DS1819
2 of 8
The DS1814/DS1819 ‘A’ and ‘C’ perform pushbutton reset control. They debounce the pushbutton input
and generate an active reset pulse width of 140 ms minimum. The DS1814/9 ‘A’ and ‘B’ versions
perform a watchdog function. The watchdog is an internal timer that forces the reset signals to the active
state if the strobe input does not change state every 1.12 seconds. The watchdog timer function can be
disabled by leaving the watchdog strobe input disconnected.
OPERATION
Power Monitor
The DS1814 detects out-of-tolerance power supply conditions and warns a processor-based system of
impending power failure. When VCC falls below a preset level, a comparator outputs the signal RST (or
RST). RST (or RST) are excellent control signals for a microprocessor, as processing is stopped at the
last possible moment of valid VCC. On power-up, RST (or RST) are kept active for a minimum of 140 ms
to allow the power supply and processor to stabilize.
Pushbutton Reset
The DS1814 ‘A’ and ‘C’ provide an input pin for direct connection to a pushbutton reset (see Figure 2).
The pushbutton reset input requires an active low signal. Internally, this input is debounced and timed
such that a RST (or RST) signal of at least 140 ms minimum will be generated. The 140 ms delay
commences as the pushbutton reset input is released from the low level (see Figure 3).
Watchdog Timer
The DS1814/DS1819 ‘A’ and ‘B’ versions watchdog timer function forces RST (and RST) signal(s)
active when the ST input is not clocked within the 1.12 second watchdog time-out period. Time-out of
the watchdog starts when RST (and RST) become(s) inactive. If a transition occurs on the ST input pin
prior to time-out, the watchdog timer is reset and begins to time out again. If the watchdog timer is
allowed to time out, then the reset output(s) will go active for 140 ms. The watchdog can be disabled by
floating (or tri-stating) the ST input.
The ST input can be derived from many microprocessor outputs. The most typical signals used are the
microprocessor data I/O signals and control signals. When the microprocessor functions normally, these
signals would as a matter of routine cause the watchdog to be reset prior to time-out. To guarantee that
the watchdog timer does not time out, a transition must occur at or less than 1.12 seconds. A typical
circuit example is shown in Figure 4. The DS1814/19 watchdog function can be disabled at any time by
tri-starting the strobe input. A sample circuit to disable the watchdog is shown in Figure 6.
相关PDF资料 |
PDF描述 |
|---|---|
| DQ65033QGL10NKS-G | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| DB1-332 | 1 ELEMENT, 33 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| DB2-393 | 1 ELEMENT, 390 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| DB3-224 | 1 ELEMENT, 2200 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| D11C0.8 | 1 ELEMENT, 0.8 uH, POWDERED IRON-CORE, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1814CR-10-U | 功能描述:电压监测器/监控器 RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| DS1814CR-10-U+ | 功能描述:电压监测器/监控器 RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| DS1814CR-5/T&R | 制造商:Maxim Integrated Products 功能描述:UMON RST PBRST SOT23 5V 5% T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MICROMON 5V W/PBRST SOT-23-5 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits 3.3/5V MicroMonitor |
| DS1814CR-5/T&R | 功能描述:监控电路 3.3/5V MicroMonitor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1814CR-5/TR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage Detector |
发布紧急采购，3分钟左右您将得到回复。