- 您现在的位置：买卖IC网 > PDF目录21993 > DS1821S/T&R (Maxim Integrated)IC THERMOMETER/STAT PROG 8-SOIC PDF资料下载
参数资料
| 型号： | DS1821S/T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/19页 |
| 文件大小： | 793K |
| 描述： | IC THERMOMETER/STAT PROG 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 系列： | 1-Wire® |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±1°C（最小值） |
| 拓扑： | 比较器，寄存器库 |
| 输出类型： | 数字 |
| 输出警报： | 无 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 带卷 (TR) |
DS1821
5 of 19
Nonvolatile write status can be monitored by reading the NVB bit in the status/configuration register:
NVB = 1 a write to EEPROM memory is in progress, NVB = 0 nonvolatile memory is idle.
THERMOSTAT MODE
In thermostat mode (T/R ?= 1), the DS1821 can operate as a standalone thermostat that triggers according
to the T
H
and T
L
trip-points programmed while the device was in 1-Wire mode. In thermostat mode the
DS1821 powers-up performing continuous temperature conversions, and the DQ pin acts as the
thermostat output. Detailed operation of the thermostat output is provided in the OPERATION
STANDALONE THERMOSTAT section of this datasheet.
Communications can be re-established with the DS1821 while it is in thermostat mode by pulling V
DD
to
0V while the DQ line is held high, and then toggling the DQ line low 16 times as shown in Figure 12.
This temporarily places the DS1821 in 1-Wire mode, allowing microprocessor communication with the
DS1821 via the DQ pin. At this time any I/O function can be performed, such as reading/writing the T
H
,
T
L
or configuration registers or reading the temperature register. To return to thermostat mode, the same
procedure can be performed (pulling V
DD
to 0V while the DQ line is held high, and then clocking the DQ
line 16 times) or the power can be cycled. Note that temporarily putting the DS1821 into 1-Wire mode
does not change the power-up mode of the device; this can only be changed by rewriting the T/R ?bit in
the status/configuration register. Also note that holding both V
DD
and DQ
low for more than
approximately 10 seconds will cause the DS1821 to be powered down.
OPERATION MEASURING TEMPERATURE
DS1821 output temperature data is calibrated in degrees centigrade and is stored in twos complement
format in the 1-byte (8-bit) temperature register (see Figure 3), which the user can access when the
DS1821 is in 1-Wire mode (T/R ?= 0 in the status/configuration register). The sign bit (S) indicates if the
temperature is positive or negative; for positive numbers S = 0 and for negative numbers S = 1. Table 2
gives examples of digital output data and the corresponding temperature reading. For Fahrenheit
measurements, a lookup table or conversion routine must be used.
The DS1821 can be configured by the user to take continuous temperature measurements (continuous
conversion mode) or single measurements (one-shot mode). The desired configuration can be achieved
by setting the nonvolatile1SHOT bit in the status/configuration register: 1SHOT = 0 continuous
conversion mode, 1SHOT = 1 one-shot mode. Note that the 1SHOT setting only controls the operation
of the device in 1-Wire mode; in thermostat mode, continuous temperature conversions are started
automatically at power-up.
In continuous conversion mode, the Start Convert T [EEh] command initiates continuous temperature
conversions, which can be stopped using the Stop Convert T [22h] command. In one-shot mode the Start
Convert T [EEh] command initiates a single temperature conversion after which the DS1821 returns to a
low-power standby state. In this mode, the microprocessor can monitor the DONE bit in the
configuration register to determine when the conversion is complete: DONE = 0 conversion in
progress, DONE = 1 conversion complete. The DONE bit does not provide conversion status in
continuous conversion mode since measurements are constantly in progress (i.e., DONE will always be
0).
TEMPERATURE, T
H
and T
L
REGISTER FORMAT Figure 3
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
S
2
6
2
5
2
4
2
3
2
2
2
1
2
0
相关PDF资料 |
PDF描述 |
|---|---|
| FAN2512S26X | IC REG LDO 2.6V .15A SOT23-5 |
| NSR0320MW2T1G | DIODE SCHOTTKY 1A 20V SOD-323 |
| 8309-8009 | CONN D-SUB RCPT 9POS W/O INSERT |
| FAN2559MP18X | IC REG LDO 1.8V .18A 6MLP |
| EBM15DRKI-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1821T | 功能描述:IC THERMOMETER/STAT PROG TO-220 RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:1-Wire® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| DS1822 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+ | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+PAR | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。