- 您现在的位置：买卖IC网 > PDF目录97865 > DS1821S (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | DS1821S |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | 0.208 INCH, SOIC-8 |
| 文件页数： | 13/17页 |
| 文件大小： | 461K |
| 代理商： | DS1821S |
DS1821
Page 5 of 17
configuration register to determine when the conversion status: DONE = 0 ― conversion in progress,
DONE = 1 ― conversion complete. The DONE bit does not provide conversion status in continuous
conversion mode since measurements are constantly in progress (i.e., DONE will always be 0).
TEMPERATURE, TH and TL REGISTER FORMAT Figure 3
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
S2
6
2
5
2
4
2
3
2
1
2
0
TEMPERATURE/DATA RELATIONSHIP Table 2
TEMPERATURE
DIGITAL OUTPUT
(Binary)
DIGITAL OUTPUT
(Hex)
+125°C*
0111 1101
7Dh
+85°C
0101 0101
55h
+25°C
0001 1001
19h
0°C
0000 0000
00h
-1°C
1111 1111
FFh
-25°C
1110 0111
E7h
-55°C
1100 1001
C9h
HIGH-RESOLUTION TEMPERATURE READINGS
The user can calculate temperature values with higher than 8-bit resolution using the data remaining in
the counter and slope accumulator when the temperature conversion is complete. To do this the user must
first read the temperature from the 8-bit temperature register. This value is called TEMP_READ in the
high-resolution equation (see Eq. 1). The 9-bit counter value must then be obtained by issuing the Read
Counter [A0h] command. This value is the count remaining in the counter at the end of the gate period
and is called COUNT_REMAIN in Eq. 1. Next the Load Counter [41h] command must be issued, which
loads the 9-bit slope accumulator value into the counter register. The slope accumulator value (called
COUNT_PER_C in Eq. 1) can then be read from the counter by again issuing the Read Counter [A0h]
command. The slope accumulator value is called “COUNT_PER_C” because it represents the number of
counts needed for an accurate measurement at a given temperature (i.e., the counts per degree C). The
high-resolution temperature can then be calculated using Eq. 1:
Eq. 1)
TEMPERATURE = TEMP_READ
0.5 +
C
PER
COUNT
REMAIN
COUNT
C
PER
COUNT
_
)
_
(
Additional information about high-resolution temperature calculations can be found in Application Note
105: “High Resolution Temperature Measurement with Dallas Direct-to-Digital Temperature Sensors”.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1821 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, ROUND, SURFACE MOUNT |
| DS1821T | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1821S/T&R | 制造商:Maxim Integrated Products 功能描述:PROGRAM THERMOSTAT 208ML 8-SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT PROG 8-SOIC |
| DS1821S/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1821S/TR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821S+ | 功能描述:板上安装温度传感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1821S+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Programmable Digital Thermostat and Thermometer |
发布紧急采购，3分钟左右您将得到回复。