- 您现在的位置：买卖IC网 > PDF目录18946 > DS1822 (Maxim Integrated)IC THERMOMETER ECONO DIG TO-92 PDF资料下载
参数资料
| 型号： | DS1822 |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | IC THERMOMETER ECONO DIG TO-92 |
| 标准包装： | 500 |
| 感应温度： | -55°C ~ 125°C |
| 输出类型： | 数字 |
| 电源电压： | 3 V ~ 5 V |
| 精确度： | ±2°C |
| 封装/外壳： | TO-226-3、TO-92-3 标准主体 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 管件 |
DS1822
SKIP ROM [CCh]
The master can use this command to address all devices on the bus simultaneously without sending out
any ROM code information. For example, the master can make all DS1822s on the bus perform
simultaneous temperature conversions by issuing a Skip ROM command followed by a Convert T [44h]
command.
Note that the Read Scratchpad [BEh] command can follow the Skip ROM command only if there is a
single slave device on the bus. In this case time is saved by allowing the master to read from the slave
without sending the device’s 64-bit ROM code. A Skip ROM command followed by a Read Scratchpad
command will cause a data collision on the bus if there is more than one slave since multiple devices will
attempt to transmit data simultaneously.
ALARM SEARCH [ECh]
The operation of this command is identical to the operation of the Search ROM command except that
only slaves with a set alarm flag will respond. This command allows the master device to determine if
any DS1822s experienced an alarm condition during the most recent temperature conversion. After every
Alarm Search cycle (i.e., Alarm Search command followed by data exchange), the bus master must return
to Step 1 (Initialization) in the transaction sequence. Refer to the OPERATION—ALARM SIGNALING
section for an explanation of alarm flag operation.
DS1822 FUNCTION COMMANDS
After the bus master has used a ROM command to address the DS1822 with which it wishes to
communicate, the master can issue one of the DS1822 function commands. These commands allow the
master to write to and read from the DS1822’s scratchpad memory, initiate temperature conversions and
determine the power supply mode. The DS1822 function commands, which are described below, are
summarized in Table 4 and illustrated by the flowchart in Figure 12.
CONVERT T [44h]
This command initiates a single temperature conversion. Following the conversion, the resulting thermal
data is stored in the 2-byte temperature register in the scratchpad memory and the DS1822 returns to its
low-power idle state. If the device is being used in parasite power mode, within 10 μ s (max) after this
command is issued the master must enable a strong pullup on the 1-Wire bus for the duration of the
conversion (t conv ) as described in the POWERING THE DS1822 section. If the DS1822 is powered by an
external supply, the master can issue read time slots after the Convert T command and the DS1822 will
respond by transmitting 0 while the temperature conversion is in progress and 1 when the conversion is
done. In parasite power mode this notification technique cannot be used since the bus is pulled high by
the strong pullup during the conversion.
WRITE SCRATCHPAD [4Eh]
This command allows the master to write three bytes of data to the DS1822’s scratchpad. The first data
byte is written into the T H register (byte 2 of the scratchpad), the second byte is written into the T L
register (byte 3), and the third byte is written into the configuration register (byte 4). Data must be
transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or
the data may be corrupted.
READ SCRATCHPAD [BEh]
This command allows the master to read the contents of the scratchpad. The data transfer starts with the
least significant bit of byte 0 and continues through the scratchpad until the 9 th byte (byte 8–CRC) is read.
The master may issue a reset to terminate reading at any time if only part of the scratchpad data is needed.
COPY SCRATCHPAD [48h]
This command copies the contents of the scratchpad T H , T L and configuration registers (bytes 2, 3, and 4)
to EEPROM. If the device is being used in parasite power mode, within 10 μ s (max) after this command is
11 of 21
相关PDF资料 |
PDF描述 |
|---|---|
| 507-4860-3732-500F | LED PANEL IND 14V 20MA GREEN |
| AH1460619-A | SWITCH MINI SPDT PLUNG GOLD PCB |
| 559-6401-003F | LED PANEL DAYLT WHT SNAP-IN 6"LD |
| 559-6201-003F | LED PANEL DAYLT GRN SNAP-IN 6"LD |
| SS-5-FD | SWITCH BASIC SPDT 5A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1822/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+ | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+PAR | 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1822+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer |
| DS1822+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
发布紧急采购，3分钟左右您将得到回复。