- 您现在的位置：买卖IC网 > Datasheet目录409 > DS1822Z/T&R (Maxim Integrated)IC THERMOMETER ECONO DIG 8-SOIC Datasheet资料下载
参数资料
| 型号： | DS1822Z/T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/21页 |
| 文件大小： | 0K |
| 描述： | IC THERMOMETER ECONO DIG 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 感应温度： | -55°C ~ 125°C |
| 输出类型： | 数字 |
| 电源电压： | 3 V ~ 5 V |
| 精确度： | ±2°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
DS1822
OPERATION—ALARM SIGNALING
After the DS1822 performs a temperature conversion, the temperature value is compared to the user-
defined two’s complement alarm trigger values stored in the 1-byte T H and T L registers (see Figure 3).
The sign bit (S) indicates if the value is positive or negative: for positive numbers S = 0 and for negative
numbers S = 1. The T H and T L registers are NV (EEPROM) so they will retain data when the device is
powered down. T H and T L can be accessed through bytes 2 and 3 of the scratchpad as explained in the
MEMORY section of this data sheet.
T H AND T L REGISTER FORMAT Figure 3
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
S
2
6
2
5
2
4
2
3
2
2
2
1
2 0
Only bits 11 through 4 of the temperature register are used in the T H and T L comparison since T H and T L
are 8-bit registers. If the measured temperature is lower than or equal to T L or higher than or equal to T H ,
an alarm condition exists and an alarm flag is set inside the DS1822. This flag is updated after every
temperature measurement; therefore, if the alarm condition goes away, the flag will be turned off after the
next temperature conversion.
The master device can check the alarm flag status of all DS1822s on the bus by issuing an Alarm Search
[ECh] command. Any DS1822s with a set alarm flag will respond to the command, so the master can
determine exactly which DS1822s have experienced an alarm condition. If an alarm condition exists and
the T H or T L settings have changed, another temperature conversion should be done to validate the alarm
condition.
POWERING THE DS1822
The DS1822 can be powered by an external supply on the V DD pin, or it can operate in “parasite power”
mode, which allows the DS1822 to function without a local external supply. Parasite power is very useful
for applications that require remote temperature sensing or that are very space constrained. Figure 1
shows the DS1822’s parasite-power control circuitry, which “steals” power from the 1-Wire bus via the
DQ pin when the bus is high. The stolen charge powers the DS1822 while the bus is high, and some of
the charge is stored on the parasite power capacitor (C PP ) to provide power when the bus is low. When the
DS1822 is used in parasite power mode, the V DD pin must be connected to ground.
In parasite power mode, the 1-Wire bus and C PP can provide sufficient current to the DS1822 for most
operations as long as the specified timing and voltage requirements are met (refer to the DC
ELECTRICAL CHARACTERISTICS and the AC ELECTRICAL CHARACTERISTICS sections of this
data sheet). However, when the DS1822 is performing temperature conversions or copying data from the
scratchpad memory to EEPROM, the operating current can be as high as 1.5mA. This current can cause
an unacceptable voltage drop across the weak 1-Wire pullup resistor and is more current than can be
supplied by C PP . To assure that the DS1822 has sufficient supply current, it is necessary to provide a
strong pullup on the 1-Wire bus whenever temperature conversions are taking place or data is being
copied from the scratchpad to EEPROM. This can be accomplished by using a MOSFET to pull the bus
directly to the rail as shown in Figure 4. The 1-Wire bus must be switched to the strong pullup within
10 μ s (max) after a Convert T [44h] or Copy Scratchpad [48h] command is issued, and the bus must be
held high by the pullup for the duration of the conversion (t conv ) or data transfer (t wr = 10ms). No other
activity can take place on the 1-Wire bus while the pullup is enabled.
The DS1822 can also be powered by the conventional method of connecting an external power supply to
the V DD pin, as shown in Figure 5. The advantage of this method is that the MOSFET pullup is not
required, and the 1-Wire bus is free to carry other traffic during the temperature conversion time.
5 of 21
相关PDF资料 |
PDF描述 |
|---|---|
| DS1870E-010+T&R | IC CNTRLR RF POWER AMP 16TSSOP |
| DS18S20-PAR+T&R | IC THERM MICROLAN HI-PREC TO-92 |
| DS60R+T&R | IC SENSOR MICRO CENTIGRADE SOT23 |
| DV164102 | KIT DEV RFPICKIT KIT 1 |
| DVK90109 | KIT DEV FOR MLX90109 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1825 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1825U | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1825U/T&R | 制造商:Maxim Integrated Products 功能描述:1-W PROGRAMMABLE DGT THERM 8P USOP - Tape and Reel |
| DS1825U/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1825U/TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
发布紧急采购，3分钟左右您将得到回复。