- 您现在的位置：买卖IC网 > Datasheet目录39 > DS1825U+T&R (Maxim Integrated)IC THERMOMETER DIGITAL 8-USOP Datasheet资料下载
参数资料
| 型号： | DS1825U+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/21页 |
| 文件大小： | 287K |
| 描述： | IC THERMOMETER DIGITAL 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | 寄存器库，变签式暂存器 |
| 输出类型： | 数字 |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 3 V ~ 3.7 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS1825 Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID
5 of 21
OPERATION?/SPAN>MEASURING TEMPERATURE
The core functionality of the DS1825 is its direct-to-digital temperature sensor. The resolution of the temperature
sensor is user-configurable to 9, 10, 11, or 12 bits, corresponding to increments of 0.5癈, 0.25癈, 0.125癈, and
0.0625癈, respectively. The default resolution at power-up is 12-bit. The DS1825 powers-up in a low-power idle
state; to initiate a temperature measurement and A-to-D conversion, the master must issue a Convert T [44h]
command. Following the conversion, the resulting thermal data is stored in the 12-bit temperature register in the
scratchpad memory and the DS1825 returns to its idle state. If the DS1825 is powered by an external supply, the
master can issue read time slots (see the 1-Wire BUS SYSTEM section) after the Convert T command and the
DS1825 will respond by transmitting 0 while the temperature conversion is in progress and 1 when the conversion
is done. If the DS1825 is powered with parasite power, this notification technique cannot be used since the bus
must be pulled high by a strong pullup during the entire temperature conversion. The bus requirements for parasite
power are explained in detail in the POWERING THE DS1825 section of this data sheet.
The DS1825 output temperature data is calibrated in degrees centigrade; for Fahrenheit applications, a lookup
table or conversion routine must be used. The temperature data is stored as a 16-bit sign-extended twos
complement number in the temperature register (see Figure 2). The sign bits (S) indicate if the temperature is
positive or negative: for positive numbers S = 0 and for negative numbers S = 1. If the DS1825 is configured for 12-
bit resolution, all bits in the temperature register will contain valid data. For 11-bit resolution, bit 0 is undefined. For
10-bit resolution, bits 1 and 0 are undefined, and for 9-bit resolution bits 2, 1 and 0 are undefined. Table 3 gives
examples of digital output data and the corresponding temperature reading for 12-bit resolution conversions.
Figure 2. TEMPERATURE REGISTER FORMAT
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
LS Byte
2
3
2
2
2
1
2
0
2
-1
2
-2
2
-3
2
-4
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
MS Byte
S
S
S
S
S
2
6
2
5
2
4
Table 3. TEMPERATURE/DATA RELATIONSHIP
TEMPERATURE
DIGITAL OUTPUT
(Binary)
DIGITAL OUTPUT
(Hex)
+125癈
0000 0111 1101 0000
07D0h
+85癈*
0000 0101 0101 0000
0550h
+25.0625癈
0000 0001 1001 0001
0191h
+10.125癈
0000 0000 1010 0010
00A2h
+0.5癈
0000 0000 0000 1000
0008h
0癈
0000 0000 0000 0000
0000h
-0.5癈
1111 1111 1111 1000
FFF8h
-10.125癈
1111 1111 0101 1110
FF5Eh
-25.0625癈
1111 1110 0110 1111
FE6Fh
-55癈
1111 1100 1001 0000
FC90h
*The power-on reset value of the temperature register is +85癈
OPERATION?/SPAN>ALARM SIGNALING
After the DS1825 performs a temperature conversion, the temperature value is compared to the user-defined twos
complement alarm trigger values stored in the 1-byte T
H
and T
L
registers (see Figure 3). The sign bit (S)
indicates if
the value is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. The T
H
and T
L
registers are NV (EEPROM) so they will retain data when the device is powered down. T
H
and T
L
can be accessed
through bytes 2 and 3 of the scratchpad as explained in the MEMORY section of this data sheet.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1842N+T&R | IC CURRENT MONITOR 14TDFN |
| DS18B20+PAR | IC THERM MICROLAN PROG-RES TO-92 |
| DS18B20Z/T&R | IC THERM MICROLAN PROG-RES 8SOIC |
| DS2740U+T&R | IC CURRENT GAUGE(15BIT) 8UMAX |
| DS28EA00U+T&R | IC THERMOMETER 1-WIRE 8-USOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1830 | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830+ | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830A | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830A+ | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1830AS | 功能描述:监控电路 Reset Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。