- 您现在的位置：买卖IC网 > PDF目录1787 > DS1834U/T&R (Maxim Integrated Products)IC ECONORST DUAL LO OPN-DR 8USOP PDF资料下载
参数资料
| 型号： | DS1834U/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/7页 |
| 文件大小： | 0K |
| 描述： | IC ECONORST DUAL LO OPN-DR 8USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 系列： | EconoReset |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 200 ms |
| 电压 - 阀值： | 3.3V，5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS1834/A/D
OUTPUT VALID CONDITIONS
All versions of the DS1834 can maintain valid outputs as long as one input remains above 1.2 volts.
However, the RST outputs on the DS1834 use a push-pull output structure which can maintain a valid
output below 1.2 volts. To sink current below 1.2 volts a resistor can be connected from RST to GND
(see Figure 5). This arrangement will maintain a valid value on the RST outputs even if all inputs are at 0
volts. During both power-up and power-down this arrangement will draw current when RST is in the high
state. A value of about 100 k ? = should be adequate to maintain a valid condition.
The DS1834A requires pull-up resistors on the outputs to maintain a valid output. The value of the
resistors is not critical in most cases but must be set low enough to pull the output to a high state. A
common value used is 10 k ? s (see Figure 6 and Figure 7).
APPLICATION DIAGRAM:
RST VALID TO 0 VOLTS V CC ON THE DS1834 Figure 5
APPLICATION DIAGRAM: DS1834A NMOS OUTPUTS Figure 6
Note: If outputs are pulled-up to different voltages the outputs can not be connected to form a wired
"AND".
APPLICATION DIAGRAM: DS1834A WIRED "AND" OUTPUT Figure 7
4 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| DS1836B-5+ | IC MICROMAN 5V ACT HI 5% 8-DIP |
| DS1861E+ | IC LASR CTRLR 1CHAN 5.5V 14TSSOP |
| DS1862AB+ | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862B+T&R | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1873T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1836 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:3.3V/5V MicroManager |
| DS1836A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| DS1836A-05 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage Detector |
| DS1836A-10 | 功能描述:监控电路 3.3/5V MicroManager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| DS1836A-10+ | 功能描述:监控电路 3.3/5V MicroManager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。