- 您现在的位置：买卖IC网 > PDF目录9171 > DS1848E-050+ (Maxim Integrated Products)IC RES/MEM TEMP 50/10K 14-TSSOP PDF资料下载
参数资料
| 型号： | DS1848E-050+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/17页 |
| 文件大小： | 0K |
| 描述： | IC RES/MEM TEMP 50/10K 14-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 接片： | 256 |
| 电阻（欧姆）： | 10k，50k |
| 电路数： | 2 |
| 温度系数： | 标准值 850 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
DS1848
6 of 17
PROGRAMMING THE LOOK-UP TABLE (LUT)
The following equation can be used to determine which resistor position setting, 00h – FFh, should be
written in the LUT to achieve a given resistance at a specific temperature.
()
(
)
[
]
()
(
)
(
)
[] a
a
-
+
-
+
-
+
-
+
-
=
2
25
1
25
1
)
,
(
C
z
C
y
x
C
w
C
v
u
R
C
R
pos
DS1848-050
a = 3.78964 for the 50kW resistor
a = 19.74866 for the 10kW resistor
DS1848-010
a = 8.394533 for both 10kW resistors
R = resistance desired at the output terminal
C = temperature in degrees Celsius
u, v, w, x, y, and z are calibration constants programmed into each of the corresponding look-up tables.
Their addresses and LSB values are given in Table 1 below. Resistor 1 variables are found in Look-Up
table 1 of the EEPROM, and Resistor 2 variables are found in Look-Up Table 2. After these values are
read, they should be overwritten with the appropriate temperature specific resistance settings. Copies of
these values can also be found in the User EEPROM memory.
LOOK-UP VARIABLE ADDRESSES Table1
Address in
LUT (HEX)
Variable
LSB
28 – 29
u
2-8
2A – 2B
v
10-6
2C – 2D
w
10-9
2E – 2F
x
2-8
30 – 31
y
10-7
32 – 33
z
10-10
When shipped from the factory, all other memory locations in the LUTs are programmed to FFh (except
bytes 00h-07h of Table 1 and 2 which may be factory programmed to values other than FFh).
Note: Memory locations 44h – 47h, which cover the temperature range (+96C to +102C), are outside
of the specified operating temperature range (-40C to +95C). However, the values stored in these
locations will act as valid resistance settings if the temperature exceeds +95C. Therefore, Dallas
Semiconductor recommends that the user program a resistance value into all LUT locations. Failure to do
so will result in the part being set to the default value.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-26L-MW | CONVERTER MOD DC/DC 28V 100W |
| VI-B14-MW-B1 | CONVERTER MOD DC/DC 48V 100W |
| DS1848E-010+ | IC RES/MEM TEMP 10/10K 14-TSSOP |
| MS27500E18B35S | CONN PLUG 66POS RT ANG W/SCKT |
| M83723/92W2025N | CONN PLUG 25POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1848E-050/S+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1848E-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV TEMP RES AND MEM 10/50K T&R - Tape and Reel |
| DS1848E-050/T&R | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1848E-050/TR | 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer, 14 Pin, Plastic, TSSOP |
| DS1848E-050+ | 功能描述:数字电位计 IC Dual Temp Controlled NV Variable Resistor RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。