- 您现在的位置：买卖IC网 > PDF目录1994 > DS1851E-010+ (Maxim Integrated Products)IC DAC DUAL NV TEMP CNTRL 8TSSOP PDF资料下载
参数资料
| 型号： | DS1851E-010+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/18页 |
| 文件大小： | 0K |
| 描述： | IC DAC DUAL NV TEMP CNTRL 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 位数： | 8 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
| 输出数目和类型： | 2 电压，单极 |
| 采样率（每秒）： | * |
DS1851
10 of 18
Sequential Address Read
Sequential reads are initiated by either a current address read or a random address read. After the master
receives the first data byte, the master responds with an acknowledge. As long as the DS1851 receives
this acknowledge after a byte is read, the master may clock out additional data words from the DS1851.
After reaching address FFh, it resets to address 00h.
The sequential read operation is terminated when the master initiates a STOP condition. The master does
not respond with a zero.
2-WIRE SERIAL PORT OPERATION
The 2-wire serial port interface supports a bidirectional data transmission protocol with device
addressing. A device that sends data on the bus is defined as a transmitter, and a device receiving data as
a receiver. The device that controls the message is called a “master.” The devices that are controlled by
the master are “slaves.” The bus must be controlled by a master device that generates the serial clock
(SCL), controls the bus access, and generates the START and STOP conditions. The DS1851 operates as
a slave on the 2-wire bus. Connections to the bus are made via the open-drain I/O lines, SDA and SCL.
The following I/O terminals control the 2-wire serial port: SDA and SCL. Timing diagrams for the 2-wire
serial port can be found in Figures 3 and 4. Timing information for the 2-wire serial port is provided in
the AC Electrical Characteristics table for 2-wire serial communications.
The following bus protocol has been defined:
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is high. Changes in the
data line while the clock line is high will be interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy: Both data and clock lines remain high.
Start data transfer: A change in the state of the data line from high to low while the clock is high
defines a START condition.
Stop data transfer: A change in the state of the data line from low to high while the clock line is high
defines the STOP condition.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2187S+ | IC RECEIVE LINE INTERFACE 20SOIC |
| DS21Q58L | IC TXRX E1 QUAD 3.3V 100-LQFP |
| DS2404B | IC ECONORAM TIMECHIP 5.5V 16SSOP |
| DS2415P+T&R | IC TIME CHIP 1-WIRE 6-TSOC |
| DS2417X/T&R | IC TIMECHIP W/INTRPT 1WIRE CSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1851E-010+ | 功能描述:数模转换器- DAC Dual Temp Controlled NV Variable Resistor RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DS1851E-010+T&R | 制造商:Maxim Integrated Products 功能描述:DAC 2CH 8BIT 8TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DAC DUAL NV TEMP CNTRL 8TSSOP |
| DS1851E-010+T&R | 功能描述:数模转换器- DAC Dual Temp Controlled NV Variable Resistor RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DS1851E-010+TRL | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| DS1851E-010TR | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Temperature-Controlled NV Digital-to-Analog Converters |
发布紧急采购，3分钟左右您将得到回复。