- 您现在的位置：买卖IC网 > PDF目录9779 > DS1852B-000+ (Maxim Integrated Products)IC MONITOR TXRX OPTICAL 25-BGA PDF资料下载
参数资料
| 型号： | DS1852B-000+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/26页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR TXRX OPTICAL 25-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 25-TFBGA，CSPBGA |
| 供应商设备封装： | 25-BGA（5x5） |
| 包装： | 管件 |
DS1852
8 of 26
DIGITAL INPUTS
The four digital inputs (Din, RSin, Fin, and Lin) can be read through the 2-wire bus. The logic levels at
these inputs are mirrored in the “logic states” byte (6Eh) in Table 00h.
2-WIRE OPERATION
Clock and Data Transitions
The SDA pin is normally pulled high with an external resistor or device. Data on the SDA pin may only
change during SCL low time periods. Data changes during SCL high periods will indicate a start or stop
conditions depending on the conditions discussed below. See Figure 2 for further details.
Start Condition
A high-to-low transition of SDA with SCL high is a start condition that must precede any other
command. See Figure 2 for further details.
Stop Condition
A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop
command places the DS1852 into a low-power mode. See Figure 2 for further details.
Acknowledge Bit
All address bytes and data bytes are transmitted through a serial protocol. The DS1852 pulls SDA low
during the ninth clock pulse to acknowledge that it has received each word.
Standby Mode
The DS1852 features a low-power mode that is automatically enabled after power-on, after a stop
command, and after the completion of all internal operations.
2-Wire Interface Reset
After any interruption in protocol, power loss, or system reset, the following steps reset the DS1852:
1) Clock up to nine cycles.
2) Look for SDA high in each cycle while SCL is high.
3) Create a start condition while SDA is high.
Device Addressing
The DS1852 must receive an 8-bit device address word following a start condition to enable a specific
device for a read or write operation. The address word is clocked into the DS1852 MSB to LSB. The
address word defaults to A0h then the R/W (READ/WRITE) bit when ASEL is a logic zero. If the R/W
bit is high, a read operation is initiated. If R/W is low, a write operation is initiated. The device address
is changed to the internal chip address (Table 03h address D0h) when ASEL is logic one. The default
internal chip address from the factory is A2h.
相关PDF资料 |
PDF描述 |
|---|---|
| SY89216VMG TR | IC RECEIVER/BUFFER 1GHZ 8-MLF |
| MAX223EWI+T | IC RS-232 DRVR/RCVR 28-SOIC |
| V300C12M150BG | CONVERTER MOD DC/DC 12V 150W |
| V300C12M150BF2 | CONVERTER MOD DC/DC 12V 150W |
| AD7853LARZ-REEL | IC ADC 12BIT SRL 200KSPS 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1852B-000/C | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-000/T&R | 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA |
| DS1852B-000/T&R | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-000+ | 功能描述:模数转换器 - ADC Optical Transceiver Diagnostic Monitor RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| DS1852B-000+T&R | 制造商:Maxim Integrated Products 功能描述:OPTICAL TRNSCVR 25BGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA 制造商:Maxim Integrated Products 功能描述:Data Converter ICs - Various Optical Transceiver Diagnostic Monitor |
发布紧急采购，3分钟左右您将得到回复。