- 您现在的位置：买卖IC网 > PDF目录9171 > DS1855B-100+ (Maxim Integrated Products)IC RES TEMP-CNTRL 10/100K 16-BGA PDF资料下载
参数资料
| 型号： | DS1855B-100+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/21页 |
| 文件大小： | 0K |
| 描述： | IC RES TEMP-CNTRL 10/100K 16-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 接片： | 100，256 |
| 电阻（欧姆）： | 10k，100k |
| 电路数： | 2 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-LBGA，CSPBGA |
| 供应商设备封装： | 16-CSBGA（4x4） |
| 包装： | 托盘 |
DS1855
15 of 21
NOTES:
1. All voltages are referenced to ground.
2. ISTBY specified with for VCC = 3.0V and 5.0V, and control port logic pins are driven to the appropriate
logic levels. Appropriate logic levels specify that logic inputs are within a 0.5V of ground or VCC for
the corresponding inactive state.
3. I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VCC is switched off.
4. A fast mode device can be used in a standard mode system, but the requirement t
SU:DAT > 250ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tRMAX + tSU:DAT = 1000 + 250 = 1250ns before the SCL line is released.
5. After this period, the first clock pulse is generated.
6. The maximum t
HD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the
SCL signal.
7. CB – Total capacitance of one bus line in picofarads, timing referenced to 0.9 x V
CC and 0.1 x VCC.
8. EEPROM write begins after a STOP condition occurs.
9. Absolute linearity is used to measure expected wiper voltage as determined by wiper position.
10. Relative linearity is used to determine the change of wiper voltage between two adjacent wiper
positions.
11. ICC specified with SDA pin open.
12. Maximum ICC is dependent on clock rates.
相关PDF资料 |
PDF描述 |
|---|---|
| V72A5H300B3 | CONVERTER MOD DC/DC 5V 300W |
| DS1803E-50+T&R | IC POT DUAL ADDRESS 50K 14-TSSOP |
| VI-2WN-MY-F1 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-2WM-MY-F3 | CONVERTER MOD DC/DC 10V 50W |
| VI-2W3-MY-F3 | CONVERTER MOD DC/DC 24V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1855B-100+ | 功能描述:数字电位计 IC Dual NV w/Memory RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1855E-010 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1855E-010/R | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-010/T | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-010/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT & MEM TSSOP T&R 10/10K - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RES TEMP-CNTRL 10/10K 14TSSOP |
发布紧急采购，3分钟左右您将得到回复。