- 您现在的位置：买卖IC网 > PDF目录9051 > DS1857B-050 (Maxim Integrated Products)IC RES TEMP 50/50K W/2MON 16-BGA PDF资料下载
参数资料
| 型号： | DS1857B-050 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/22页 |
| 文件大小： | 0K |
| 描述： | IC RES TEMP 50/50K W/2MON 16-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 810 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 50 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-LBGA，CSPBGA |
| 供应商设备封装： | 16-CSBGA（4x4） |
| 包装： | 托盘 |
DS1857
Dual Temperature-Controlled Resistors with
External Temperature Input and Monitors
____________________________________________________________________
19
byte must match the address programmed into Table 01
8Ch or A0h (for the Auxiliary Device). If a device address
match occurs, this part will output a zero for one clock
cycle as an acknowledge and the corresponding block of
memory is enabled (see the Memory Organization sec-
tion). If the R/W bit is high, a read operation is initiated. If
the R/W is low, a write operation is initiated (see the
Memory Organization section). If the address does not
match, this part returns to a low-power mode.
Write Operations
After receiving a matching address byte with the R/W
bit set low, provided there is no write protect, the
device goes into the write mode of operation (see the
Memory Organization section). The master must trans-
mit an 8-bit EEPROM memory address to the device to
define the address where the data is to be written. After
the byte has been received, the DS1857 transmits a
zero for one clock cycle to acknowledge the address
has been received. The master must then transmit an
8-bit data word to be written into this address. The
DS1857 again transmits a zero for one clock cycle to
acknowledge the receipt of the data. At this point, the
master must terminate the write operation with a stop
condition. The DS1857 then enters an internally timed
write process tw to the EEPROM memory. All inputs are
disabled during this byte write cycle.
Page Write
The DS1857 is capable of an 8-byte page write. A page
is any 8-byte block of memory starting with an address
evenly divisible by eight and ending with the starting
address plus seven. For example, addresses 00h
through 07h constitute one page. Other pages would
be addresses 08h through 0Fh, 10h through 17h, 18h
through 1Fh, etc.
A page write is initiated the same way as a byte write,
but the master does not send a STOP condition after
the first byte. Instead, after the slave acknowledges the
data byte has been received, the master can send up
to seven more bytes using the same nine-clock
sequence. The master must terminate the write cycle
with a STOP condition or the data clocked into the
DS1857 will not be latched into permanent memory.
The address counter rolls on a page during a write. The
counter does not count through the entire address
space as during a read. For example, if the starting
address is 06h and 4 bytes are written, the first byte
goes into address 06h. The second goes into address
07h. The third goes into address 00h (not 08h). The
fourth goes into address 01h. If more than 9 bytes or
more are written before a STOP condition is sent, the
first bytes sent are overwritten. Only the last 8 bytes of
data are written to the page.
Acknowledge Polling: Once the internally timed write
has started and the DS1857 inputs are disabled,
acknowledge polling can be initiated. The process
involves transmitting a start condition followed by the
device address. The R/W bit signifies the type of opera-
tion that is desired. The read or write sequence will only
be allowed to proceed if the internal write cycle has
completed and the DS1857 responds with a zero.
Read Operations
After receiving a matching address byte with the R/W bit
set high, the device goes into the read mode of opera-
tion. There are three read operations: current address
read, random read, and sequential address read.
Current Address Read
The DS1857 has an internal address register that main-
tains the address used during the last read or write
operation, incremented by one. This data is maintained
as long as VCC is valid. If the most recent address was
the last byte in memory, then the register resets to the
first address.
Once the device address is clocked in and acknowl-
edged by the DS1857 with the R/W bit set to high, the
current address data word is clocked out. The master
does not respond with a zero, but does generate a stop
condition afterwards.
Single Read
A random read requires a dummy byte write sequence to
load in the data byte address. Once the device and data
address bytes are clocked in by the master, and
acknowledged by the DS1857, the master must generate
another start condition. The master now initiates a current
address read by sending the device address with the
R/W bit set high. The DS1857 acknowledges the device
address and serially clocks out the data byte.
Sequential Address Read
Sequential reads are initiated by either a current
address read or a random address read. After the mas-
ter receives the first data byte, the master responds
with an acknowledge. As long as the DS1857 receives
this acknowledge after a byte is read, the master can
clock out additional data words from the DS1857. After
reaching address FFh, it resets to address 00h.
The sequential read operation is terminated when the
master initiates a stop condition. The master does not
respond with a zero.
For a more detailed description of 2-wire theory of
operation, see the following section.
相关PDF资料 |
PDF描述 |
|---|---|
| FST3245QSC | IC SWITCH BUS 8BIT TTL 20QSOP |
| MS3108A28-2S | CONN PLUG 14POS RT ANG W/SCKT |
| MS3120F-20-41S | CONN RECEPT 41POS W/SOCKT CRIMP |
| IDT2309A-1DCGI | IC CLK BUFFER ZD STD DRV 16-SOIC |
| DS1855E-010/T&R | IC RES TEMP-CNTRL 10/10K 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1857B-050+ | 功能描述:数字电位计 IC Dual Temp-Controlled Resistors RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1857E-050 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1857E-050/R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with External Temperature Input and Monitors |
| DS1857E-050/T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with External Temperature Input and Monitors |
| DS1857E-050+ | 功能描述:数字电位计 IC Dual Temp-Controlled Resistors RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。