- 您现在的位置：买卖IC网 > PDF目录1913 > DS1857E-050+ (Maxim Integrated Products)IC RES TEMP 50/50K 2MON 16-TSSOP PDF资料下载
参数资料
| 型号： | DS1857E-050+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC RES TEMP 50/50K 2MON 16-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 50 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
DS1857
Dual Temperature-Controlled Resistors with
External Temperature Input and Monitors
____________________________________________________________________
21
data is transmitted on SDA by the DS1857, while
the serial clock is input on SCL. Start and stop
conditions are recognized as the beginning and
end of a serial transfer.
3)
Slave Address: Command/control byte is the first
byte received following the start condition from the
master device. The command/control byte con-
sists of a 4-bit control code. For the DS1857, this
is set as 1010 binary for read/write operations. The
next three bits of the command/control byte are
the device select bits or device address. They are
used by the master device to select which of eight
possible devices on the bus is to be accessed.
When reading or writing the DS1857, the device-
select bits must match one of two valid device
addresses 00h, or the address registered in Table
01 location 8Ch. The last bit of the command/con-
trol byte (R/W) defines the operation to be per-
formed. When set to a ‘1’ a read operation is
selected, and when set to a ‘0’ a write operation is
selected. The slave address can be set by the
EEPROM.
Following the start condition, the DS1857 monitors the
SDA bus checking the device type identifier being
transmitted. Upon receiving the 1010 control code, the
appropriate device address bits, and the read/write bit,
the slave device outputs an acknowledge signal on the
SDA line.
Chip Topology
TRANSISTOR COUNT: 44149
SUBSTRATE CONNECTED TO GROUND.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 5. 2-Wire Data Transfer Protocol
相关PDF资料 |
PDF描述 |
|---|---|
| DS1857E-050 | IC RES TEMP 50/50K 2MON 16-TSSOP |
| DS1858E-050 | IC RES TEMP 50/50K 3MON 16-TSSOP |
| DS1859E-015+ | IC RES DUAL TEMP-CTRL 16-TSSOP |
| DS1865T+ | IC PON TRIPLEXER CTRLR 28TQFN-EP |
| DS1866Z/T&R | IC POT TRIM LOG 2.7-5.5V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1857E-050/R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with External Temperature Input and Monitors |
| DS1857E-050/T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with External Temperature Input and Monitors |
| DS1857E-050+ | 功能描述:数字电位计 IC Dual Temp-Controlled Resistors RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1858 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual Temperature-Controlled Resistors with Three Monitors |
| DS1858B-050 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。