- 您现在的位置：买卖IC网 > PDF目录9184 > DS1866Z+T&R (Maxim Integrated Products)IC POT TRIM LOG 2.7-5.5V 8-SOIC PDF资料下载
参数资料
| 型号： | DS1866Z+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/5页 |
| 文件大小： | 0K |
| 描述： | IC POT TRIM LOG 2.7-5.5V 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接片： | 8 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 3 输入并口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
DS1866
5 of 5
102199
NOTES:
1. All voltages are referenced to ground.
2. For VCC = 5V ± 10% maximum VIL = +0.8V. For VCC 3.0 ± 10% VIL = +0.6V. For VCC =2.7 volts VIH
=2.0 volts minimum.
3. Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4. Maximum current specifications are based on the change rate of the parallel port inputs P0, P1, and
P2.
5. Standby current specifications apply when P0, P1, P2 logic inputs are driven within the specified VIH
or VIL levels.
6. Valid at 25
°C only.
7. The end-to-end resistance tolerance of the DS1866 can be expected to shift with temperature.
However, this change will not exceed ±20% of the nominal resistor value of the part.
8. Absolute tolerance is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1866 is specified to provide an absolute tolerance of ±1.0 dB.
9. Tap-to-tap tolerance is used to determine the change in voltage between successive tap positions. The
DS1866 is specified to provide a tap-to-tap tolerance specification of ±1.0 dB.
10. -3 dB cutoff frequency characteristic for the DS1866 is 1 MHz.
11. Capacitance values apply at 25°C.
12. This specification refers to the time difference between parallel port input changes to stabilize a wiper
transition.
DS1866 ORDERING INFORMATION
ORDERING NUMBER
PACKAGE
OPERATING
TEMPERATURE
VERSION
DS1866
8L DIP
-40°C TO +85°C
10k
DS1866Z
8L SOIC (150-MIL)
-40°C TO +85°C
10k
相关PDF资料 |
PDF描述 |
|---|---|
| MK2059-01SILF | IC VCXO CLK JITTER ATTEN 20-SOIC |
| VI-B4W-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| VI-B4V-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
| MS27468E25F35SA | CONN RCPT 128POS JAM NUT W/SCKT |
| MS27656T17B6P | CONN RCPT 6POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1867 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Digital Potentiometer with EEPROM |
| DS1867-010 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Digital Potentiometer with EEPROM |
| DS1867-050 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dual Digital Potentiometer with EEPROM |
| DS1867-10 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1867-10+ | 功能描述:数字电位计 IC Dual w/EEPROM RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。