- 您现在的位置：买卖IC网 > PDF目录1914 > DS1882Z-050+T&R (Maxim Integrated Products)IC POT DIGIT DL LOG 50K 16SOIC PDF资料下载
参数资料
| 型号： | DS1882Z-050+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | IC POT DIGIT DL LOG 50K 16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接片： | 64 |
| 电阻（欧姆）： | 45k |
| 电路数： | 2 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 4.5 V ~ 7 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
DS1882
Dual Log Audio Digital Potentiometer
____________________________________________________________________
13
setup time (see Figure 4) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse, and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses, including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An Acknowledge-
ment (ACK) or Not Acknowledge (NACK) is always the
9th bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave
during a write operation) performs an ACK by transmit-
ting a zero during the 9th bit. A device performs a
NACK by transmitting a one during the 9th bit. Timing
(Figure 4) for the ACK and NACK is identical to all other
bit writes. An ACK is the acknowledgment that the
device is properly receiving data. A NACK is used to
terminate a read sequence or as an indication that the
device is not receiving data.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 3. Data Transfer Protocol
SDA
SCL
tHD:STA
tLOW
tHIGH
tR
tF
tHD:DAT
tSU:DAT
REPEATED
START
tSU:STA
tHD:STA
tSU:STO
tSP
STOP
START
tBUF
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
Figure 4. I2C Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| DS1884AT+T | IC SFP PON ONU CTRLR 24TQFN |
| DS2105Z+ | IC SCSI TERMINATOR 16-SOIC |
| DS2106S/T&R | IC TERMINATOR SCSI 28-SOIC |
| DS2108S+T&R | IC TERM SCSI DIFF/SWITCH 24-SOIC |
| DS2114Z | IC TERM SCSI 2% 150MIL 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1884AT+ | 功能描述:ADC / DAC多通道 SFP and PON ONU Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1884AT+T | 功能描述:ADC / DAC多通道 SFP and PON ONU Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1884T+ | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Digi LDD Interface RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1884T+T | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Digi LDD Interface RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1886 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:带有数字LDD接口的SFP和PON ONU控制器 |
发布紧急采购，3分钟左右您将得到回复。