参数资料
型号: DS18B20+
厂商: Maxim Integrated
文件页数: 7/22页
文件大小: 528K
描述: IC THERM MICROLAN PROG-RES TO-92
产品培训模块: 1-Wire Communications
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 500
功能: 温度计,恒温计
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±2°C(最小值)
拓扑: 寄存器库,变签式暂存器
输出类型: 1-Wire?
输出警报:
输出风扇:
电源电压: 3 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 通孔
封装/外壳: TO-226-3、TO-92-3 标准主体
供应商设备封装: TO-92-3
包装: 管件
产品目录页面: 1435 (CN2011-ZH PDF)
DS18B20
 
7 of 22 
MEMORY
The DS18B20s memory is organized as shown in Figure 7. The memory consists of an SRAM
scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (T
H
 and T
L
)
and configuration register. Note that if the DS18B20 alarm function is not used, the T
H
 and T
L
 registers
can serve as general-purpose memory. All memory commands are described in detail in the DS18B20 
Function Commands section. 
Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,
respectively. These bytes are read-only. Bytes 2 and 3 provide access to T
H
 and T
L
 registers. Byte 4
contains the configuration register data, which is explained in detail in the Configuration Register section.
Bytes 5, 6, and 7 are reserved for internal use by the device and cannot be overwritten.
Byte 8 of the scratchpad is read-only and contains the CRC code for bytes 0 through 7 of the scratchpad.
The DS18B20 generates this CRC using the method described in the CRC Generation section.
Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command; the data
must be transmitted to the DS18B20 starting with the least significant bit of byte 2. To verify data
integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is
written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least
significant bit of byte 0. To transfer the T
H
, T
L
 and configuration data from the scratchpad to EEPROM,
the master must issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM to
the scratchpad at any time using the Recall E
2
 [B8h] command. The master can issue read time slots
following the Recall E
2
 command and the DS18B20 will indicate the status of the recall by transmitting 0
while the recall is in progress and 1 when the recall is done.
Figure 7. DS18B20 Memory Map
 
SCRATCHPAD
(POWER-UP STATE) 
 
Byte 0   Temperature LSB (50h)
 
 
Byte 1   Temperature MSB (05h)
 
EEPROM
Byte 2   T
H
 Register or User Byte 1*
 
T
H
 Register or User Byte 1
Byte 3   T
L
 Register or User Byte 2*
 
T
L
 Register or User Byte 2
Byte 4   Configuration Register*
 
Configuration Register
Byte 5   Reserved (FFh)
 
 
Byte 6   Reserved
 
 
Byte 7   Reserved (10h)
 
 
Byte 8   CRC*
 
 
*Power-up state depends on value(s) stored in EEPROM.
 
85癈  
相关PDF资料
PDF描述
XC95288XL-7BGG256C IC CPLD 288MCELL 7.5NS 256-PBGA
TMK316BJ335ML-T CAP CER 3.3UF 25V 20% X5R 1206
ASC31DRTS-S93 CONN EDGECARD 62POS DIP .100 SLD
ECC22DJBN-S1136 CONN EDGECARD 44PS .100 PRESSFIT
ADSP-BF527KBCZ-6 IC DSP CTRLR 16B 600MHZ 289BGA
相关代理商/技术参数
参数描述
DS18B20/GG8 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE RESOLUTION 1-WIRE DIGITAL THERMOMETER - Rail/Tube
DS18B20/T&R 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES TO-92
DS18B20/T&R 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS18B20_07 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Resolution 1-Wire Digital Thermometer
DS18B20_08 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1-Wire Digital Thermometer