- 您现在的位置：买卖IC网 > PDF目录97865 > DS18B20-PAR/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT PDF资料下载
参数资料
| 型号： | DS18B20-PAR/T&R |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| 封装： | TO-92, 3 PIN |
| 文件页数： | 13/19页 |
| 文件大小： | 203K |
| 代理商： | DS18B20-PAR/T&R |
DS18B20-PAR
3 of 19
PARASITE POWER
The DS18B20-PAR’s parasite power circuit allows the DS18B20-PAR to operate without a local external
power supply. This ability is especially useful for applications that require remote temperature sensing or
that are very space constrained. Figure 1 shows the DS18B20-PAR’s parasite-power control circuitry,
which “steals” power from the 1-Wire bus via the DQ pin when the bus is high. The stolen charge
powers the DS18B20-PAR while the bus is high, and some of the charge is stored on the parasite power
capacitor (CPP) to provide power when the bus is low.
The 1-Wire bus and CPP can provide sufficient parasite power to the DS18B20-PAR for most operations
as long as the specified timing and voltage requirements are met (refer to the DC ELECTRICAL
CHARACTERISTICS and the AC ELECTRICAL CHARACTERISTICS sections of this data sheet).
However, when the DS18B20-PAR is performing temperature conversions or copying data from the
scratchpad memory to EEPROM, the operating current can be as high as 1.5 mA. This current can cause
an unacceptable voltage drop across the weak 1-Wire pullup resistor and is more current than can be
supplied by CPP. To assure that the DS18B20-PAR has sufficient supply current, it is necessary to
provide a strong pullup on the 1-Wire bus whenever temperature conversions are taking place or data is
being copied from the scratchpad to EEPROM. This can be accomplished by using a MOSFET to pull
the bus directly to the rail as shown in Figure 2. The 1-Wire bus must be switched to the strong pullup
within 10
μs (max) after a Convert T [44h] or Copy Scratchpad [48h] command is issued, and the bus
must be held high by the pullup for the duration of the conversion (tconv) or data transfer (twr = 10 ms).
No other activity can take place on the 1-Wire bus while the pullup is enabled.
SUPPLYING THE DS18B20-PAR DURING TEMPERATURE CONVERSIONS
Figure 2
OPERATION – MEASURING TEMPERATURE
The core functionality of the DS18B20-PAR is its direct-to-digital temperature sensor. The resolution of
the temperature sensor is user-configurable to 9, 10, 11, or 12 bits, which corresponds to increments of
0.5
°C, 0.25°C, 0.125°C, and 0.0625°C, respectively. The default resolution at power-up is 12-bit.
The DS18B20-PAR powers-up in a low-power idle state; to initiate a temperature measurement and A-to-
D conversion, the master must issue a Convert T [44h] command.
Following the conversion, the
resulting thermal data is stored in the 2-byte temperature register in the scratchpad memory and the
DS18B20-PAR returns to its idle state.
The DS18B20-PAR output data is calibrated in degrees
centigrade; for Fahrenheit applications, a lookup table or conversion routine must be used.
The
temperature data is stored as a 16-bit sign-extended two’s complement number in the temperature register
(see Figure 3). The sign bits (S) indicate if the temperature is positive or negative: for positive numbers S
= 0 and for negative numbers S = 1. If the DS18B20-PAR is configured for 12-bit resolution, all bits in
the temperature register will contain valid data. For 11-bit resolution, bit 0 is undefined. For 10-bit
VPU
4.7K
1-Wire Bus
Micro-
processor
DS18B20-PAR
GND
DQ
To Other
1-Wire Devices
相关PDF资料 |
PDF描述 |
|---|---|
| DS18B20-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, ROUND, THROUGH HOLE MOUNT |
| DS18B20P | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20X | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS18B20 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS18B20-SL | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Resolution 1-Wire Digital Thermometer |
| DS18B20-SL/T&R | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS18B20-SL+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL SERL (1-WIRE) - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr |
| DS18B20-SL+T&R | 功能描述:板上安装温度传感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS18B20U | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。