参数资料
| 型号： | DS21349Q+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/35页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1 3.3V 28-PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | 线路接口装置（LIU） |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
DS21349
22 of 35
10. DIAGNOSTIC MODE OPERATION
The DS21349 offers several diagnostic modes as listed in Table 10-A. Various diagnostic modes are only
available in software mode. In hardware mode, the diagnostic modes are selected by a combination of pin
settings. In software mode, the diagnostic modes are selected by setting appropriate bits in the diagnostic
control register.
Table 10-A. Diagnostic Modes
AVAILABILITY
SOFTWARE MODE
DIAGNOSTIC MODE
HARDWARE
SOFTWARE
MASKABLE
Local Loopback (LLB)
Yes
No
Analog Loopback (ALB)
Yes
No
Remote Loopback (RLB)
Yes
No
In-Band Network Loopback (NLB)
Yes
Dual Loopback (DLOOP)
Yes
No
Internal Data Pattern Generation and Detection
Transmit AIS (TAIS)
Yes
No
Quasirandom Signal Source (QRSS)
Yes
In-Band Loop-Up/Down Code Generator
No
Yes
No
Error Insertion and Detection
Bipolar Violation Insertion (INSBPV)
Yes
No
Logic Error Insertion (INSLER)
Yes
No
Bipolar Violation Detection (BPV)
Yes
No
Logic Error Detection, QRSS (QPD)
Yes
No
Alarm Condition Monitoring
Receive Carrier Loss (RCL) Monitoring
Yes
Receive Alarm Indication Signal (AIS) Monitoring
No
Yes
Transmit Driver Failure Monitoring (DFMO)
No
Yes
Jitter Attenuator Limit Trip (JALT)
No
Yes
Other Diagnostic Reports
Receive Line Attenuation Indicator (LATN)
No
Yes
No
10.1 Loopback Modes
10.1.1 Local Loopback (LLB)
When local loopback is enabled (set LLB in CR2, or pull the LLB pin high), inbound data at the receiver
inputs are ignored. TCLK and TPOS/TNEG pass through the jitter attenuator if enabled and are output at
RCLK and RPOS/RNEG. The transmit path is unaffected by LLB, and will continue to transmit data
normally (or AIS if TAIS is enabled).
10.1.2 Analog Loopback (ALB)
When analog loopback (ALB) is enabled (set ALB in CR2, or float the LLB pin), the receiver input pins
are disconnected from the clock and data recovery circuit and replaced by TTIP and TRING. This tests
the entire device including the jitter attenuator, transmitter, and receiver circuits.
10.1.3 Remote Loopback (RLB)
When remote loopback (RLB) is enabled (set RLB in CR2, or pull RLB pin high), inbound data at the
receiver inputs is looped back to the transmitter path. Data passes through the jitter attenuator if enabled.
The B8ZS encoder and decoder are not included in the loopback path. The receive path continues to
operate normally.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21352LB | IC TXRX 1-CHIP T1 3.3V 100-LQFP |
| DS21372TN | IC TESTER BIT ERROR 3.3V 32-TQFP |
| DS2141AQN | IC CONTROLLER T1 5V 44-PLCC |
| DS2143QN/T&R | IC CONTROLLER E1 5V LP 44-PLCC |
| DS21448L | IC LIU QUAD E1/T1/J1 128-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21349Q/T&R+ | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 3.3V 28PLCC - Tape and Reel |
| DS21349Q/T&R | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21349Q+ | 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21349Q+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 3.3V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 3.3V 28-PLCC |
| DS21349Q+T&R | 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。