- 您现在的位置：买卖IC网 > PDF目录10993 > DS21372TN+ (Maxim Integrated Products)IC TESTER BIT ERROR 3.3V 32-TQFP PDF资料下载
参数资料
| 型号： | DS21372TN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | IC TESTER BIT ERROR 3.3V 32-TQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 250 |
| 功能： | 位误码率测试器（BERT） |
| 接口： | T1 |
| 电路数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 10mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-TQFP |
| 供应商设备封装： | 32-TQFP（7x7） |
| 包装： | 托盘 |
| 包括： | 错误计数器，样式发生器和检测器 |
DS21372
4 of 22
DETAILED PIN DESCRIPTION Table 1
PIN
SYMBOL
TYPE
DESCRIPTION
1TL
I
Transmit Load. A positive-going edge loads the pattern generator with
the contents of the Pattern Set Registers. The MSB of the repetitive or
pseudorandom pattern appears at TDATA after the third positive edge of
TCLK from asserting TL. TL is logically OR’ed with PCR.7 and should
be tied to VSS if not used. See Figure 8 for timing information.
2
AD0
I/O
Data Bus. An 8-bit multiplexed address/data bus.
3
AD1
I/O
Data Bus. An 8-bit multiplexed address/data bus.
4
TEST
I
Test. Set high to 3-state all output pins ( INT , ADx, TDATA, RLOS).
Should be tied to VSS to enable all outputs.
5VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
6
AD2
I/O
Data Bus. An 8-bit multiplexed address/data bus.
7
AD3
I/O
Data Bus. An 8-bit multiplexed address/data bus.
8
AD4
I/O
Data Bus. An 8-bit multiplexed address/data bus.
9
AD5
I/O
Data Bus. An 8-bit multiplexed address/data bus.
10
AD6
I/O
Data Bus. An 8-bit multiplexed address/data bus.
11
AD7
I/O
Data Bus. An 8-bit multiplexed address/data bus.
12
VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
13
VDD
-
Positive Supply. 3.3V.
14
BTS
I
Bus Type Select. Strap high to select Motorola bus timing; strap low to
select Intel bus timing. This pin controls the function of the RD (DS),
ALE(AS), and WR (R/ W ) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
15
RD
(DS)
I
Read Input (Data Strobe).
16
CS
I
Chip Select. Must be low to read or write the port.
17
ALE(AS)
I
Address Latch Enable (Address Strobe). A positive going edge serves
to demultiplex the bus.
18
WR
(R/ W )
I
Write Input (Read/Write).
19
INT
O
Alarm Interrupt. Flags host controller during conditions defined in
Status Register. Active low, open drain output.
20
VDD
-
Positive Supply. 3.3V.
21
VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
22
LC
I
Load Count. A positive-going edge latches the current bit and bit error
count into the user accessible BCR and BECR registers and clears the
internal count registers. LC is logically OR’ed with control bit PCR.4.
Should be tied to VSS if not used.
23
RLOS
O
Receive Loss Of Sync. Indicates the real time status of the receive
synchronizer. Active high output.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B0R-IY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
| DS3170N+ | IC TXRX DS3/E3 100-CSBGA |
| DS2151QB | IC TXRX T1 1-CHIP 5V LP 44-PLCC |
| DS21Q58LN+ | IC TXRX E1 QUAD 3.3V 100LQFP |
| DS26504LN+ | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21372TN+ | 功能描述:网络控制器与处理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS214 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2141A | 功能描述:网络控制器与处理器 IC T1 Controller w/Elastic Store RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2141AN | 功能描述:网络控制器与处理器 IC T1 Controller w/Elastic Store RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2141AQ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。