参数资料
型号: DS2148T
厂商: Maxim Integrated Products
文件页数: 24/73页
文件大小: 0K
描述: IC LIU E1/T1/J1 5V 44-TQFP
产品培训模块: Lead (SnPb) Finish for COTS
产品变化通告: Product Discontinuation 20/Feb/2012
标准包装: 160
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: T1/E1/J1
电源电压: 4.75 V ~ 5.25 V
安装类型: 表面贴装
封装/外壳: 44-TQFP
供应商设备封装: 44-TQFP(10x10)
包装: 管件
DS2148/DS21Q48
30 of 73
CCR3 (02H): COMMON CONTROL REGISTER 3
(MSB)
(LSB)
TUA1
ATUA1
TAOZ
TPRBSE
TLCE
LIRST
IBPV
IBE
SYMBOL
POSITION
DESCRIPTION
TUA1
CCR3.7
Transmit Unframed All Ones. The polarity of this bit is set such
that the device will transmit an all ones pattern on power-up or
device reset. This bit must be set to a one to allow the device to
transmit data. The transmission of this data pattern is always timed
off of the JACLK (See Figure 1-1).
0 = transmit all ones at TTIP and TRING
1 = transmit data normally
ATUA1
CCR3.6
Automatic Transmit Unframed All Ones. Automatically transmit
an unframed all ones pattern at TTIP and TRING during a receive
carrier loss (RCL) condition or a receive all ones condition.
0 = disabled
1 = enabled
TAOZ
CCR3.5
Transmit Alternate Ones and Zeros. Transmit a …101010…
pattern at TTIP and TRING. The transmission of this data pattern is
always timed off of TCLK (See Figure 1-1).
0 = disabled
1 = enabled
TPRBSE
CCR3.4
Transmit PRBS Enable. Transmit a 215 - 1 (E1) or a 220 - 1 (T1)
PRBS at TTIP and TRING. See Figure 1-3.
0 = disabled
1 = enabled
TLCE
CCR3.3
Transmit Loop Code Enable. Enables the transmit side to
transmit the loop up code in the Transmit Code Definition registers
(TCD1 and TCD2). See Section 4 and Figure 1-3 for details.
0 = disabled
1 = enabled
LIRST
CCR3.2
Line Interface Reset. Setting this bit from a zero to a one will
initiate an internal reset that resets the clock recovery state machine
and re-centers the jitter attenuator. Normally this bit is only toggled
on power-up. Must be cleared and set again for a subsequent reset.
IBPV
CCR3.1
Insert BPV. A 0 to 1 transition on this bit will cause a single
Bipolar Violation (BPV) to be inserted into the transmit data
stream. Once this bit has been toggled from a 0 to a 1, the device
waits for the next occurrence of three consecutive ones to insert the
BPV. This bit must be cleared and set again for a subsequent error
to be inserted. See Figure 1-3.
IBE
CCR3.0
Insert Bit Error. A 0 to 1 transition on this bit will cause a single
logic error to be inserted into the transmit data stream. This bit
must be cleared and set again for a subsequent error to be inserted.
相关PDF资料
PDF描述
DS2149Q+ IC LIU T1/J1 5V 28-PLCC
DS2151QN IC TXRX T1 1-CH 5V LP IND 44PLCC
DS2152L+ IC TXRX T1 1CHIP ENHNCD 100-LQFP
DS2153Q-A7+T&R IC TXRX E1 1-CHIP 5V 44-PLCC
DS2154LNA2+ IC TXRX E1 5V 100-LQFP
相关代理商/技术参数
参数描述
DS2148T+ 功能描述:网络控制器与处理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2148TA2 功能描述:网络控制器与处理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2148TB 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2148TC1 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2148TN 功能描述:网络控制器与处理器 IC 5V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray