- 您现在的位置：买卖IC网 > PDF目录97866 > DS2151QNB (MAXIM INTEGRATED PRODUCTS INC) DATACOM, FRAMER, PQCC44 PDF资料下载
参数资料
| 型号： | DS2151QNB |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PQCC44 |
| 封装： | 0.652 INCH, PLASTIC, LCC-44 |
| 文件页数： | 16/62页 |
| 文件大小： | 921K |
| 代理商： | DS2151QNB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
DS2151Q
23 of 60
Table 5-2. Alarm Set and Clear Criteria
ALARM
SET CRITERIA
CLEAR CRITERIA
Blue Alarm (AIS) (see note below)
When over a 3ms window, five or
less 0s are received
When over a 3ms window, six or
more 0s are received
Yellow Alarm
1. D4 bit 2 mode (RCR2.2=0)
2. D4 12th F-bit mode (RCR2.2=1;
this mode is also referred to as
the “Japanese Yellow Alarm”)
3. ESF Mode
When bit 2 of 256 consecutive
channels is set to 0 for at least 254
occurrences
When the 12th framing bit is set to
1 for two consecutive occurrences
When 16 consecutive patterns of
00FF hex appear in the FDL
When bit 2 of 256 consecutive
channels is set to 0 for less than 254
occurrences
When the 12th framing bit is set to 0
for two consecutive occurrences
When 14 or less patterns of 00FF
hex out of 16 possible appear in the
FDL
Red Alarm (RCL) (this alarm is
also referred to as Loss of Signal)
When 192 consecutive 0s are
received
When 14 or more 1s out of 112
possible bit positions are received
starting with the first 1 received
Note: The definition of Blue Alarm (or Alarm Indication Signal) is an unframed all-ones signal. Blue alarm detectors should
be able to operate properly in the presence of a 10-3 error rate and they should not falsely trigger on a framed all-ones signal.
The blue alarm criteria in the DS2151Q has been set to achieve this performance. It is recommended that the RBL bit be
qualified with the RLOS status bit in detecting a blue alarm.
5.1
Loop Up/Down Code Detection
Bits SR1.7 and SR1.6 will indicate when either the standard Loop Up or Loop Down codes are being
received by the DS2151Q. When a Loop Up code has been received for 5 seconds, the CPE is expected to
loop the recovered data (without correcting BPVs) back to the source. The Loop Down code indicates
that the loopback should be discontinued. See the AT&T publication TR 62411 for more details. The
DS2151Q will detect the Loop Up/Down codes in both framed and unframed circumstances with bit error
rates as high as 10**-2. The loop code detector has a nominal integration period of 48ms. Hence, after
about 48ms of receiving either code, the proper status bit will be set to a 1. After this initial indication, it
is recommended that the software poll the DS2151Q every 100ms to 500ms until 5 seconds have elapsed
to insure that the code is continuously present. Once 5 seconds have passed, the DS2151Q should be
taken into or out of loopback via the Remote Loopback (RLB) bit in CCR1.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2151QB | DATACOM, FRAMER, PQCC44 |
| DS2152LN | DATACOM, FRAMER, PQFP100 |
| DS2152L | DATACOM, FRAMER, PQFP100 |
| DS2153Q | DATACOM, FRAMER, PQCC44 |
| DS2154L | DATACOM, FRAMER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2151QNB/T&R | 制造商:Maxim Integrated Products 功能描述:T1 SINGLE CHIP XCVR REV B IND - Tape and Reel |
| DS2151QNB/T&R | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2151QNB+ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2151QNB+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel |
| DS2151QNB+T&R | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。