- 您现在的位置：买卖IC网 > PDF目录10237 > DS2165QN+ (Maxim Integrated Products)IC PROC ADPCM 16/24/32K 28-PLCC PDF资料下载
参数资料
| 型号： | DS2165QN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | IC PROC ADPCM 16/24/32K 28-PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | ADPCM 处理器 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 管件 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
DS2165Q
2 of 17
OVERVIEW
The DS2165Q contains three major functional blocks: a high performance (10 MIPS) DSP engine, two
independent PCM interfaces (X and Y) that connect directly to serial time-division-multiplexed (TDM)
backplanes, and a serial port that can configure the device on-the-fly by an external controller. A 10MHz
master clock is required by the DSP engine. The DS2165Q can be configured to perform either two
expansions, two compressions, or one expansion and one compression. The PCM/ADPCM data interfaces
support data rates from 256kHz to 4.096MHz. Typically, the PCM data rates are 1.544MHz for
m-law and
2.048MHz for A-law. Each channel on the device samples the serial input PCM or ADPCM bit stream
during a user-programmed input time slot, processes the data and outputs the result during a user-
programmed output time slot.
Each PCM interface has a control register that specifies functional characteristics (compress, expand,
bypass, and idle), data format (
m-law or A-law), and algorithm reset control. With the SPS pin strapped
high, the software mode is enabled and the serial port can be used to configure the device. In this mode, a
novel addressing scheme allows multiple devices to share a common 3-wire control bus, simplifying
system-level interconnect.
With SPS low, the hardware mode is enabled. This mode disables the serial port and maps certain control
register bits to some of the address and serial port pins. Under the hardware mode, no external host
controller is required and all PCM/ADPCM input and output time slots default to time slot 0.
HARDWARE RESET
RST
allows the user to reset both channel algorithms and the contents of the internal registers. This pin
must be held low for at least 1ms on system power-up after the master clock is stable to ensure that the
device has initialized properly. RST should also be asserted when changing to or from the hardware
mode. RST clears all bits of the control register for both channels except the IPD bits; the IPD bits for
both channels are set to 1.
SOFTWARE MODE
Connecting SPS high enables the software mode. In this mode, an external host controller writes
configuration data to the DS2165Q by the serial port through inputs SCLK, SDI, and CS (Figure 2). Each
write to the DS2165Q is either a 2-byte write or a 4-byte write. A 2-byte write consists of the
address/command byte (ACB), followed by a byte to configure the control register (CR) for either the X
or Y channel. The 4-byte write consists of the ACB, followed by a byte to configure the CR, and then 1
byte to set the input time slot and another byte to set the output time slot.
ADDRESS/COMMAND BYTE
In the software mode, the address/command byte is the first byte written to the serial port; it identifies
which of the 64 possible ADPCM processors sharing the port wiring is to be updated. Address data must
match that at inputs A0 to A5. If no match occurs, the device ignores the following configuration data. If
an address match occurs, the next 3 bytes written are accepted as control, input and output time slot data.
Bit ACB.6 determines which side (X or Y) of the device is to be updated. The PCM and ADPCM outputs
are tri-stated during register updates.
相关PDF资料 |
PDF描述 |
|---|---|
| 24292-31PG-300 | CONN RCPT 31POS PNL MNT PIN |
| CXS3102A1812S | CONN RCPT 6POS PNL MNT SKT |
| FSA221MUX | IC SWITCH AUD USB DPDT 10-MSOP |
| CXS3102A184S | CONN RCPT 4POS PNL MNT SKT |
| EN3P13M26X | CONN RCPT 13POS MALE PANEL #26 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2165QN/T&R | 制造商:Maxim Integrated Products 功能描述:ADPCM PROCESSOR 16/24/32KBS IND T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC ADPCM PROCESSOR PLCC 制造商:Maxim Integrated Products 功能描述:Audio DSPs 16/24/32kbps ADPCM Processor |
| DS2165QN/T&R+ | 制造商:Maxim Integrated Products 功能描述:ADPCM PROCESSOR PLCC IND T&R LF - Tape and Reel |
| DS2165QN/T&R | 功能描述:音频 DSP 16/24/32kbps ADPCM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| DS2165QN+ | 功能描述:音频 DSP 16/24/32kbps ADPCM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| DS2165QN+T&R | 制造商:Maxim Integrated Products 功能描述:ADPCM PROCESSOR 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PROC ADPCM 16/24/32K 28-PLCC 制造商:Maxim Integrated Products 功能描述:Audio DSPs 16/24/32kbps ADPCM Processor |
发布紧急采购，3分钟左右您将得到回复。