参数资料
型号: DS2172T+
厂商: Maxim Integrated Products
文件页数: 17/22页
文件大小: 0K
描述: IC TESTER BIT ERROR RATE 32-TQFP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 250
功能: 位误码率测试器(BERT)
接口: T1
电路数: 1
电源电压: 4.5 V ~ 5.5 V
电流 - 电源: 10mA
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 32-TQFP
供应商设备封装: 32-TQFP(7x7)
包装: 托盘
包括: 错误计数器,样式发生器和检测器
产品目录页面: 1429 (CN2011-ZH PDF)
DS2172
4 of 22
DETAILED PIN DESCRIPTION Table 1
PIN
SYMBOL
TYPE
DESCRIPTION
1TL
I
Transmit Load. A positive-going edge loads the pattern generator with
the contents of the Pattern Set Registers. The MSB of the repetitive or
pseudorandom pattern appears at TDATA after the third positive edge of
TCLK from asserting TL. TL is logically OR’ed with PCR.7 and should
be tied to VSS if not used. See Figure 8 for timing information.
2
AD0
I/O
Data Bus. An 8-bit multiplexed address/data bus.
3
AD1
I/O
Data Bus. An 8-bit multiplexed address/data bus.
4
TEST
I
Test. Set high to 3-state all output pins ( INT , ADx, TDATA, RLOS).
Should be tied to VSS to enable all outputs.
5VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
6
AD2
I/O
Data Bus. An 8-bit multiplexed address/data bus.
7
AD3
I/O
Data Bus. An 8-bit multiplexed address/data bus.
8
AD4
I/O
Data Bus. An 8-bit multiplexed address/data bus.
9
AD5
I/O
Data Bus. An 8-bit multiplexed address/data bus.
10
AD6
I/O
Data Bus. An 8-bit multiplexed address/data bus.
11
AD7
I/O
Data Bus. An 8-bit multiplexed address/data bus.
12
VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
13
VDD
-
Positive Supply. 5.0V.
14
BTS
I
Bus Type Select. Strap high to select Motorola bus timing; strap low to
select Intel bus timing. This pin controls the function of the RD (DS),
ALE(AS), and WR (R/ W ) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
15
RD
(DS)
I
Read Input (Data Strobe).
16
CS
I
Chip Select. Must be low to read or write the port.
17
ALE(AS)
I
Address Latch Enable (Address Strobe). A positive going edge serves
to demultiplex the bus.
18
WR
(R/ W )
I
Write Input (Read/Write).
19
INT
O
Alarm Interrupt. Flags host controller during conditions defined in
Status Register. Active low, open drain output.
20
VDD
-
Positive Supply. 5.0V.
21
VSS
-
Signal Ground. 0.0V. Should be tied to local ground plane.
22
LC
I
Load Count. A positive-going edge latches the current bit and bit error
count into the user accessible BCR and BECR registers and clears the
internal count registers. LC is logically OR’ed with control bit PCR.4.
Should be tied to VSS if not used.
23
RLOS
O
Receive Loss Of Sync. Indicates the real time status of the receive
synchronizer. Active high output.
相关PDF资料
PDF描述
VE-B1Z-IY-F3 CONVERTER MOD DC/DC 2V 20W
CPC1465MTR IC SHDSL/ISDN DC TERM 16-MLP
VE-B1Z-IY-F2 CONVERTER MOD DC/DC 2V 20W
73M1906B-IM/F MICRODAA SET FXO OF VOIP 32-QFN
73M1906B-IVT/F MICRODAA SET FXO OF VOIP 20TSSOP
相关代理商/技术参数
参数描述
DS2172T/T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC TESTER BIT ERROR RATE 32-TQFP 制造商:Maxim Integrated Products 功能描述:Telecom ICs Bit Error Rate Tester (BERT)
DS2172T/T&R+ 制造商:Maxim Integrated Products 功能描述:BERT 32P TQFP T&R LEAD FREE - Tape and Reel
DS2172T/T&R 功能描述:电信集成电路 Bit Error Rate Tester (BERT) RoHS:否 制造商:STMicroelectronics 类型:Telecom IC - Various 工作电源电压:4.75 V to 5.25 V 电源电流: 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-100 封装:Tray
DS2172T+ 功能描述:电信集成电路 Bit Error Rate Tester (BERT) RoHS:否 制造商:STMicroelectronics 类型:Telecom IC - Various 工作电源电压:4.75 V to 5.25 V 电源电流: 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-100 封装:Tray
DS2172T+T&R 制造商:Maxim Integrated Products 功能描述:BIT ERROR RATE TESTER 32TQFP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TESTER BIT ERROR RATE 32-TQFP 制造商:Maxim Integrated Products 功能描述:Telecom ICs Bit Error Rate Tester (BERT)