- 您现在的位置：买卖IC网 > PDF目录97867 > DS2180A (MAXIM INTEGRATED PRODUCTS INC) DATACOM, FRAMER, PDIP40 PDF资料下载
参数资料
| 型号： | DS2180A |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PDIP40 |
| 封装： | 0.600 INCH, DIP-40 |
| 文件页数： | 19/35页 |
| 文件大小： | 481K |
| 代理商： | DS2180A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
DS2180A
26 of 35
make it compatible with bipolar transmission techniques and inserts zero suppression codes. The bipolar
coder also supports the onboard loopback feature. Input-to-output delay of the transmitter is 10 TCLK
cycles.
RECEIVE SIDE OVERVIEW
Synchronizer
The heart of the receiver is the synchronizer monitor. This circuit serves two purposes: 1) monitoring the
incoming data stream for loss of frame or multiframe alignment, and 2) searching for new frame
alignment pattern when sync loss is detected. When sync loss is detected, the synchronizer begins an off-
line search for the new alignment; all output timing signals remain at the old alignment with the exception
of RSIGFR, which is forced low during resync. When one and only one candidate is qualified, the output
timing will move to the new alignment at the beginning of the next multiframe. One frame later, RLOS
will transition low, indicating valid sync and the resumption of the normal sync monitoring mode. Several
bits in the RCR allow tailoring of the resync algorithm by the user. These bits are described below.
Sync Time (RCR.2)
Bit RCR.2 determines the number of consecutive framing pattern bits to be qualified before SYNC is
declared. If RCR.2=1, the algorithm will validate 24 bits; if RCR.2=0, 10 bits are validated. 24-bit
testing results in superior false framing protection, while 10-bit testing minimizes reframe time (although
in either case, the synchronizer will only establish resync when one and only one candidate is found).
Resync (RCR.0)
A 0-to-1 transition of RCR.0 causes the synchronizer to search for the framing pattern sequence
immediately, regardless of the internal sync status. In order to initiate another resync command, this bit
must be cleared and then set again.
Sync Enable (RCR.1)
When RCR.1 is cleared, the receiver will initiate automatic resync if any of the following events occur: 1)
an OOF event (“out-of-frame”), or 2) carrier loss (32 consecutive 0’s appear at RPOS and RNEG). An
OOF event occurs any time that 2 of 4 F T or FPS bits are in error. When RCR.1 is set, the automatic
resync circuitry is disabled; in this case, resync can only be initiated by setting RCR.0 to 1 or externally
via a low-high transition on RST . Note that using RST to initiate resync resets the receive output timing
while RST is low; use of RCR.1 does not affect output timing until the new alignment is located.
Sync Criteria (RCR.3)
193E
Bit RCR.3 determines which sync algorithm is utilized when resync is in progress (RLOS=1). In 193E
framing, when RCR.3=0, the synchronizer will lock only to the FPS pattern and will move to the new
frame and multiframe alignment after the move to the new alignment.
When RCR.3=1, the new
alignment is further tested by a CRC code match. RLOS will transition low after a CRC match occurs. If
no CRC match occurs in three attempts (three multiframes), the algorithm will reset and a new search for
the framing pattern begins. It takes 9 ms for the synchronizer to check the first CRC code after the new
alignment has been loaded. Each additional CRC test takes 3 ms. Regardless of the state of RCR.3, if
more than one candidate exists after about 24 ms, the synchronizer will begin eliminating emulators by
testing their CRC codes online in order to find the true framing candidate.
193S
In 193S framing, when RCR.3=1, the synchronizer will cross check the FT pattern with the FS pattern to
help eliminate false framing candidates such as digital milliwatts. The FS patterns are compared to the
相关PDF资料 |
PDF描述 |
|---|---|
| DS2180AN | DATACOM, FRAMER, PDIP40 |
| DS2181AN | DATACOM, FRAMER, PDIP40 |
| DS2181AQN | DATACOM, FRAMER, PQCC44 |
| DS2181A | DATACOM, FRAMER, PDIP40 |
| DS2181AQ | DATACOM, FRAMER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2180A+ | 功能描述:网络控制器与处理器 IC T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2180AN | 功能描述:网络控制器与处理器 IC T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2180AQ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2180AQ/T&R | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver |
| DS2180AQ/T&R+ | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。