参数资料
型号: DS2180AQ
厂商: Maxim Integrated Products
文件页数: 33/35页
文件大小: 0K
描述: IC TRANSCEIVER T1 44-PLCC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 28
功能: 收发器
接口: T1
电路数: 1
电源电压: 4.5 V ~ 5.5 V
电流 - 电源: 3mA
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.59x16.59)
包装: 管件
包括: 警报生成和检测,B7 填充模式,B8ZS 模式,错误检测和计数器,“硬件”模式,透明模式
DS2180A
7 of 35
ACB: ADDRESS COMMAND BYTE Figure 4
(MSB)
(LSB)
-
FRSR2
EYELMD
FM
SYELMD
B8ZS
B7
LPBK
SYMBOL
POSITION
NAME AND DESCRIPTION
-
CCR.7
Reserved, must be 0 for proper operation.
FRSR2
CCR.6
Function of REC Status Register 2.
0 = Detected B8ZS code words reported at RSR.2.
1 = COFA (Change-of-Frame Alignment) reported at RSR.2 when
last resync resulted in change of frame or multiframe alignment.
EYELMD
CCR.5
193E Yellow Mode Select.
0 = Yellow alarm is a repeating pattern set of 00 hex and FF hex.
1 = Yellow alarm is a 0 in the bit 2 position of all channels.
FM
CCR.4
Frame Mode Select.
0 = D4 (193S, 12 frames/superframe).
1 = Extended (193E, 24 frames/superframe).
SYELMD
CCR.3
193S Yellow Mode Select. Determines yellow alarm type to be
transmitted and detected while in 193S framing. If set, yellow
alarms are a 1 in the S-bit position of frame 12; if cleared, yellow
alarm is a 0 in bit 2 of all channels. Does not affect 193E yellow
alarm operation.
B8ZS
CCR.2
Bipolar eight zero substitution.
0 = No B8ZS.
1 = B8ZS enabled.
(Note: This bit must be set to 0 when CCR.1=1)
B7
CCR.1
Bit seven zero suppression. If CCR.1=1, channels with an all zero
content will be transmitted with bit 7 forced to 1. If CCR.1=0, no
bit 7 stuffing occurs.
(Note: This bit must be set to 0 when CCR.2=1)
LPBK
CCR.0
Loopback. When set, the device internally loops output transmit
data into the incoming receive data buffers and TCLK is internally
substituted for RCLK.
LOOPBACK (Refer to Figure 4)
Enabling loopback will typically induce an out-of-frame (OOF) condition. If appropriate bits are set in
the receive control register, the receiver will resync to the looped transmit frame alignment. During the
looped condition, the transmit outputs (TPOS, TNEG) will transmit unframed all 1's. All operating modes
(B8ZS, alarm, signaling, etc.) except for blue alarm transmission are available in loopback.
BIT SEVEN STUFFING
Existing systems meet 1's density requirements by forcing bit 7 of all zero channels to 1. Bit 7 stuffing is
globally enabled by asserting bit CCR.1 and may be disabled on an individual channel basis by setting
appropriate bits in TTR1–TTR3. Bit 7 stuffing and B8ZS modes should not be enabled simultaneously.
Enabling both results in LOS.
相关PDF资料
PDF描述
VI-B5N-IY-F1 CONVERTER MOD DC/DC 18.5V 50W
VI-B5L-IY-F3 CONVERTER MOD DC/DC 28V 50W
MC9S08AC32CFGE IC MCU 8BIT 32K FLASH 44-LQFP
VI-B5V-IY-F1 CONVERTER MOD DC/DC 5.8V 50W
MC9S08DZ32AMLC IC MCU 32K FLASH 2K RAM 32-LQFP
相关代理商/技术参数
参数描述
DS2180AQ/T&R 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver
DS2180AQ/T&R+ 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel
DS2180AQ/T&R 功能描述:网络控制器与处理器 IC T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2180AQ+ 功能描述:网络控制器与处理器 IC T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2180AQ+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/T1 5V 44PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver