- 您现在的位置：买卖IC网 > PDF目录9559 > DS21Q48N (Maxim Integrated Products)IC LIU E1/T1/J1 4X 5V LONG144BGA PDF资料下载
参数资料
| 型号： | DS21Q48N |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/73页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1/T1/J1 4X 5V LONG144BGA |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 规程： | E1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-BBGA |
| 供应商设备封装： | 144-PBGA（17x17） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
DS2148/DS21Q48
24 of 73
3.2 Parallel Port Operation
When using the parallel interface on the DS2148 (BIS1 = 0) the user has the option for either multiplexed
bus operation (BIS1 = 0, BIS0 = 0) or nonmultiplexed bus operation (BIS1 = 0, BIS0 = 1). The DS2148
can operate with either Intel or Motorola bus timing configurations. If the PBTS pin is tied low, Intel
timing will be selected; if tied high, Motorola timing will be selected. All Motorola bus signals are listed
in parentheses. See the timing diagrams in Section 10 for more details.
3.3 Serial Port Operation
Setting BIS1 = 1 and BIS0 = 0 enables the serial bus interface on the DS2148. Port read/write timing is
unrelated to the system transmit and receive timing, allowing asynchronous reads or writes by the host.
See Section 10 for the AC timing of the serial port. All serial port accesses are LSB first. See Figure 3-1,
Reading or writing to the internal registers requires writing one address/command byte prior to
transferring register data. The first bit written (LSB) of the address/command byte specifies whether the
access is a read (1) or a write (0). The next 5 bits identify the register address. Bit 7 is reserved and must
be set to 0 for proper operation.
The last bit (MSB) of the address/command byte is the burst mode bit. When the burst bit is enabled
(B = 1) and a READ operation is performed, addresses 0 through 15h are read sequentially, starting at
address 0h. And when the burst bit is enabled and a WRITE operation is performed, addresses 0 through
16h are written sequentially, starting at address 0h. Burst operation is stopped once address 15h is read.
See Figure 3-5 and Figure 3-6 for more details.
All data transfers are initiated by driving the
CS input low. When input clock-edge select (ICES) is low,
input data is latched on the rising edge of SCLK and when ICES is high, input data is latched on the
falling edge of SCLK. When output clock-edge select (OCES) is low, data is output on the falling edge of
SCLK and when OCES is high, data is output on the rising edge of SCLK. Data is held until the next
falling or rising edge. All data transfers are terminated if the
CS input transitions high. Port control logic
is disabled and SDO is tri-stated when
CS is high.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-262-MX-F4 | CONVERTER MOD DC/DC 15V 75W |
| VE-B6Y-MY-S | CONVERTER MOD DC/DC 3.3V 33W |
| DS21Q348N | IC LIU T1/E1/J1 QUAD 3.3V 144BGA |
| MS3451L18-1SW | CONN RCPT 10POS CBL MNT W/SCKT |
| D38999/26MH53SB | CONN PLUG 53POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21Q48NB | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q50 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Quad E1 Transceiver |
| DS21Q50L | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q50L+ | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q50L-C01 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。