- 您现在的位置：买卖IC网 > PDF目录1914 > DS21S07AS+T&R (Maxim Integrated Products)IC TERMINATOR SCSI 16-SOIC PDF资料下载
参数资料
| 型号： | DS21S07AS+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/8页 |
| 文件大小： | 0K |
| 描述： | IC TERMINATOR SCSI 16-SOIC |
| 标准包装： | 1,000 |
| 类型： | SCSI，LVD，SE |
| 端子数： | 9 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
DS21S087A
2 of 8
FUNCTIONAL DESCRIPTION
The DS21S07A consists of a bandgap reference, buffer amplifier, and nine termination resistors
(Figure 1). The bandgap reference circuit produces a precise 2.55V level that is fed to a buffer amplifier.
The buffer produces a 2.85V level and can source at least 24mA into each of the termination resistors
when the signal line is low (active). When the driver for a given signal line turns off, the terminator pulls
the signal line to 2.85V (quiescent state). To handle actively negated SCSI signals, the buffer can sink at
least 200mA, and VREF will move less than 60mV. When all lines settle in the quiescent state, the
regulator consumes about 2.5mA. When the DS21S07A is put into power-down mode by bringing
PD
low, the power-down circuitry turns off the transistors on each signal line. This isolates the DS21S07A
from the signal lines and effectively removes it from the circuit. The power-down pin (
PD) has an internal
50k
pullup resistor. To place the DS21S07A into an active state, the PD pin should be left open
circuited. When installed on disk drives or RAID system components, the DS21S07A will not affect the
SCSI bus during a hot plug operation.
To ensure proper operation, both the TERMPWR1 and TERMPWR2 pins must be connected to the SCSI
bus TERMPWR line and both the VREF1 and VREF2 pins must be tied together externally. Each
DS21S07A requires a 4.7
F capacitor connected between the VREF pins and ground. Figure 2 details a
typical SCSI bus configuration. In an 8-bit-wide SCSI bus arrangement (“A” Cable), two DS21S07A’s
would be needed at each end of the SCSI cable to terminate the 18 active signal lines. In a 16-bit-wide
SCSI bus arrangement (“P” Cable), three DS21S07A’s would be needed at each end of the SCSI cable to
terminate the 27 active signal lines.
Figure 1. DS21S087A Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| DS21T05Z/T&R | IC TERMINATOR SCSI 150MIL 16SOIC |
| DS21T07S+T&R | IC TERMINATOR SCSI 16-SOIC |
| DS2250-64-16+ | IC MCU 64KB 16MHZ 40-SIMM |
| DS2251T-128-16 | IC MICROCNTRLR 128K 16MHZ 72SIMM |
| DS2252T-128-16 | IC MICROCNTRLR 128K 16MHZ 40SIMM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21S07CE | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| DS21S07CS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| DS21T05 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:SCSI Terminator |
| DS21T05S | 功能描述:SCSI 接口集成电路 RoHS:否 制造商:Texas Instruments 工作电源电压:2.7 V to 5.25 V 电源电流:13 mA 最大工作温度:+ 70 C 最小工作温度:0 C 安装风格:SMD/SMT 封装 / 箱体:SSOP-36 封装:Tube |
| DS21T05S/T&R | 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI 300MIL 16SOIC |
发布紧急采购，3分钟左右您将得到回复。