- 您现在的位置：买卖IC网 > PDF目录1915 > DS21T07S+T&R (Maxim Integrated Products)IC TERMINATOR SCSI 16-SOIC PDF资料下载
参数资料
| 型号： | DS21T07S+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/7页 |
| 文件大小： | 0K |
| 描述： | IC TERMINATOR SCSI 16-SOIC |
| 标准包装： | 1,000 |
| 类型： | SCSI，LVD，SE |
| 端子数： | 9 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
DS21T07
2 of 7
FUNCTIONAL DESCRIPTION
The DS21T07 consists of a bandgap reference, buffer amplifier, and nine termination resistors (Figure 1).
The bandgap reference circuit produces a precise 2.55V level which is fed to a buffer amplifier. The
buffer produces a 2.85V level and is capable of sourcing at least 24 mA into each of the termination
resistors when the signal line is low (active). When the driver for a given signal line turns off, the
terminator will pull the signal line to 2.85V (quiescent state). To handle actively negated SCSI signals,
the buffer can sink at least 200 mA, and VREF will move less than 60 mV. When all lines settle in the
quiescent state, the regulator will consume about 5 mA. When the DS21T07 is put into power-down
mode by bringing PD low, the power-down circuitry will turn off the transistors on each signal line. This
will isolate the DS21T07 from the signal lines and effectively remove it from the circuit. The power-
down pin ( PD ) has an internal 50K
=pullup resistor. To place the DS21T07 into an active state, the PD
pin should be left open circuited. When installed on disk drives or RAID system components, the
DS21T07 will not affect the SCSI bus during a hot plug operation.
To ensure proper operation, both the TERMPWR1 and TERMPWR2 pins must be connected to the SCSI
bus TERMPWR line and both the VREF1 and VREF2 pins must be tied together externally. Each
DS21T07 requires a 4.7 F capacitor connected between the VREF pins and ground. Figure 2 details a
typical SCSI bus configuration. In an 8-bit wide SCSI bus arrangement, two DS21T07’s would be needed
at each end of the SCSI cable in order to terminate the 18 active signal lines. In a 16-bit wide SCSI bus
arrangement, three DS21T07’s would be needed at each end of the SCSI cable in order to terminate the
27 active signal lines.
DS21T16 BLOCK DIAGRAM Figure 1
相关PDF资料 |
PDF描述 |
|---|---|
| DS2250-64-16+ | IC MCU 64KB 16MHZ 40-SIMM |
| DS2251T-128-16 | IC MICROCNTRLR 128K 16MHZ 72SIMM |
| DS2252T-128-16 | IC MICROCNTRLR 128K 16MHZ 40SIMM |
| DS2291/87-22291-000 | IC STIK T1 LONG LOOP 5V 30-SIP |
| DS229S/T&R | IC TXRX TRI 5V RS-232 IND 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21T09 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Plug and Play SCSI Terminator |
| DS21T09S | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Plug and Play SCSI Terminator |
| DS21T09S/T&R | 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI P&P 28-SOIC |
| DS21T09S/T&R | 功能描述:IC TERMINATOR SCSI P&P 28-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| DS21T09S+ | 功能描述:SCSI 接口集成电路 RoHS:否 制造商:Texas Instruments 工作电源电压:2.7 V to 5.25 V 电源电流:13 mA 最大工作温度:+ 70 C 最小工作温度:0 C 安装风格:SMD/SMT 封装 / 箱体:SSOP-36 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。