参数资料
型号: DS2250T-32-16+
厂商: Maxim Integrated Products
文件页数: 15/18页
文件大小: 0K
描述: IC MCU 32KB 16MHZ 40-SIMM
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
系列: DS225x
核心处理器: 8051
芯体尺寸: 8-位
速度: 16MHz
连通性: SIO,UART/USART
外围设备: 电源故障复位,WDT
输入/输出数: 32
程序存储器类型: SRAM
RAM 容量: 32K x 8
电压 - 电源 (Vcc/Vdd): 4.75 V ~ 5.25 V
振荡器型: 外部
工作温度: 0°C ~ 70°C
封装/外壳: 40-SIMM
包装: 托盘
产品目录页面: 703 (CN2011-ZH PDF)
DS2250(T)
6 of 18
SERIAL BOOTSTRAP LOADER
The Serial Program Load Mode is the easiest, fastest, most reliable, and most complete method of
initially loading application software into the DS2250(T) nonvolatile RAM. Communication can be
performed over a standard asynchronous serial communications port. A typical application would use a
simple RS232C serial interface to program the DS2250(T) as a final production procedure. The hardware
configuration which is required for the Serial Program Load Mode is illustrated in Figure 3. Port pins 2.7
and 2.6 must be either open or pulled high to avoid placing the device in a parallel load cycle. Although
an 11.0592 MHz crystal is shown in Figure 3, a variety of crystal frequencies and loader baud rates are
supported, shown in Table 2. The serial loader is designed to operate across a 3-wire interface from a
standard UART. The receive, transmit, and ground wires are all that are necessary to establish
communication with the DS2250(T).
The Serial Bootstrap Loader implements an easy-to-use command line interface which allows an
application program in an Intel hex representation to be loaded into and read back from the device. Intel
hex is the typical format which existing 8051 cross-assemblers output. The serial loader responds to
single character commands which are summarized below:
COMMAND
FUNCTION
C
Return CRC-16 checksum of embedded RAM
D
Dump Intel hex File
F
Fill embedded RAM block with constant
K
Load 40-bit encryption key
L
Load Intel hex file
R
Read MCON register
T
Trace (Echo) incoming Intel hex data
U
Clear Security Lock
V
Verify Embedded RAM with incoming Intel hex
W
Write MCON register
Z
Set security lock
P
Put a value to a port
G
Get a value from a port
Table 1 summarizes the selection of the available Parallel Program Load cycles. The timing associated
with these cycles is illustrated in the electrical specs.
PARALLEL PROGRAM LOAD CYCLES Table 1
MODE
RST
PSEN
PROG
EA
P2.7
P2.6
P2.5
Program
1
0
VPP
1
0
X
Security Set
1
0
VPP
1
X
Verify
1
X
1
0
X
Prog Expanded
1
0
VPP
0
1
0
Verify Expanded
1
0
1
0
1
0
Prog MCON or Key registers
1
0
VPP
0
1
Verify MCON registers
1
0
1
0
1
相关PDF资料
PDF描述
VE-J1K-IW-F2 CONVERTER MOD DC/DC 40V 100W
GRM219R71H273KA01J CAP CER 0.027UF 50V 10% X7R 0805
VE-J6K-IY-F3 CONVERTER MOD DC/DC 40V 50W
VE-J1J-IW-F2 CONVERTER MOD DC/DC 36V 100W
MS27656T25B4S CONN RCPT 56POS WALL MNT W/SCKT
相关代理商/技术参数
参数描述
DS2250T-32-16+ 功能描述:模块化系统 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
DS2250T-32-8 功能描述:模块化系统 - SOM RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
DS2250T64-08 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller
DS2250T-64-12 功能描述:模块化系统 - SOM RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
DS2250T-64-16 功能描述:模块化系统 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in